Diagnostic Test

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
NOTE:
Diagnose all Front Axle Locker circuit related DTCs before continuing.
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. With the scan tool, run a Vehicle Scan Report or record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Turn the ignition off for at least 10.0 seconds.
5. Turn the ignition on.
6. Using the recorded Environmental Data and the When Monitored Conditions, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
Did the DTC return?

Yes
- Go To 2
No
- Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE DTCM HARNESS CONNECTOR AND TERMINALS
1. Turn the ignition off.
2. Check the DTCM harness connector for proper connection at the Rear Differential.
3. Verify that the connector is completely plugged in and locked prior to disconnecting.
4. Disconnect the DTCM harness connector and check for pushed out or spread terminals, brineling on terminals, discoloration from excessive heat, or corrosion and water intrusion.
  Were any issues found with the connector or terminals?
  
  Yes
  - Repair the found issues in accordance with the service information or properly connect and lock the DTCM harness connector.
  - Perform the DTCM VERIFICATION TEST. Refer to DTCM VERIFICATION TEST .
  No
  - Go To 3
REPLACE THE FRONT AXLE LOCKER SENSOR AND CHECK FOR THE DTC TO RETURN
1. Replace the Front Axle Locker Sensor in accordance with the Service Information. Refer to REMOVAL AND INSTALLATION .
2. Connect the component and ECU harness connectors.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the Environmental Data or When Monitored information above, operate the vehicle within the conditions that set the DTC.
6. With the scan tool, read DTCs.
Did the DTC return?

Yes
- Go To 4
No
- Replacing the Front Axle Locker Sensor corrected the condition.
- Perform the DTCM VERIFICATION TEST. Refer to DTCM VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all Drivetrain Control Module (DTCM) harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all DTCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read DTCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the DTCM in accordance with the Service information. Refer to MODULE, DRIVETRAIN CONTROL (DTCM), REMOVAL AND INSTALLATION .
  - Perform the DTCM VERIFICATION TEST. Refer to DTCM VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform the DTCM VERIFICATION TEST. Refer to DTCM VERIFICATION TEST .