Diagnostic Test

WARNING: This page is about a different car, the 2022 Chrysler Voyager and 2022 Chrysler Pacifica. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data and any DTCs.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go to 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (L6) RIGHT STOP/TURN FEED CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the Right Turn Signal off.
2. Turn the ignition off.
3. Disconnect the Right Tail Lamp Assembly harness connector.
4. Disconnect the BCM C5/E harness connector.
5. Turn the ignition on.
6. Measure the voltage on the (L6) Right Stop/Turn Feed circuit at the Right Tail Lamp Assembly harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the short to voltage in the (L6) Right Stop/Turn Feed circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (L6) RIGHT STOP/TURN FEED CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Measure the resistance of the (L6) Right Stop/Turn Feed circuit between the Right Tail Lamp Assembly harness connector and the BCM C5/E harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the open in the (L6) Right Stop/Turn Feed circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (Z922) GROUND CIRCUIT FOR AN OPEN
1. Measure the resistance between ground and the (Z922) Ground circuit at the Right Tail Lamp Assembly harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 5
  No
  - Repair the open in the (Z922) Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE RIGHT REAR TURN SIGNAL
1. Turn the ignition off.
2. Connect the BCM C5/E harness connector.
3. Connect a 12-volt test light between the (L6) Right Stop/Turn Feed circuit and the Ground circuit at the Right Tail Lamp Assembly harness connector.
4. Turn the ignition on.
5. Turn the Right Turn Signal on.
  Does the test light blink on and off?
  
  Yes
  - Replace the Right Rear Turn Lamp Bulb in accordance with the Service Information. Refer to LAMP, TAIL, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 6
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.