Torque Specifications
TORQUE SPECIFICATIONS
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
| Air Cleaner Body Cover Screws | 4 | - | 35 | |
| Air Cleaner Body Mounting Bracket Nuts | 8 | - | 71 | |
| Alternator to Alternator Bracket & Engine Block | 23 | 17 | - | |
| Balance Shaft Module Bolts | Refer to INSTALLATION . | |||
| Balance Shaft Chain Guide to Ladder Frame | 12 | 9 | - | |
| B+ Cable to Starter | 10 | - | 89+ | |
| B+ Cable to Generator | 12 | 9 | - | |
| Camshaft Bearing Cap Bolts | Refer to INSTALLATION . | |||
| Camshaft Sprocket Bolt | 10 + 65° | - | 89 + 65° | |
| Clean Air Hose Band Clamps | 5 | - | 44 | |
| Connecting Rod Caps | 20 + 92° | 15 + 92° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Coolant Reservoir | 9 | - | 80 | |
| Coolant Temperature Sensor | 50 | 37 | - | |
| Crankshaft Main Bearing Caps | Refer to BEARING(S), CRANKSHAFT, MAIN/STANDARD PROCEDURE . | |||
| Crankshaft Position Sensor Bolt | 9 | - | 80 | |
| Crankshaft Damper | 50 + 68° | 37 + 68° | - | |
| Cylinder Head | Refer to INSTALLATION . | |||
| Cylinder Head Main Oil Gallery M10 Tapered Plug | 5 + 72° | - | 44 + 72° | |
| Engine Cover Ball Stud to Cylinder Head Cover | 3 | - | 27 | |
| Engine Harness to Block | 12 | 9 | - | |
| Engine to Transmission | 50 | 37 | - | |
| Exhaust Manifold to Cylinder Head | 34 | 25 | - | |
| Exhaust Manifold Heat Shield | 12 | 9 | - | |
| Exhaust Pipe to Oil Pan | 25 | 18 | - | |
| Flexplate Bolts | 29 + 51° | 21 + 51° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Front Exhaust Camshaft Cap | 15 | 11 | - | |
| Heater Return to Left (Trans) Mount Bracket | 8 | - | 71 | |
| Intake Manifold to Cylinder Head Nuts and Bolts | 12 | 9 | - | |
| Intake Manifold Silencer Cover | 3 | - | 27 | |
| Intake Manifold Lower Support Bracket | 9 | - | 80 | |
| Intermediate Shaft Bracket to Engine Block | 55 | 41 | - | |
| Knock Sensor to Engine Block | 28 | 21 | - | |
| Ladder Frame to Block | Refer to FRAME, LADDER, INSTALLATION . | |||
| Left Engine Mount to Adapter Bracket | 157 | 116 | - | |
| Left Engine Mount to Frame Rail | 105 | 77 | - | |
| Left Engine Mount to Strut Tower | 64 | 47 | - | |
| Maniverter to Support Bracket | 20 | 15 | - | |
| MultiAir Fill Port Plug to Cylinder Head Cover | 21 | 15 | - | |
| Oil Cooler Heat Shield Bolts | 8 | - | 71 | |
| Oil Cooler Connector Bolt | 40 | 30 | - | |
| Oil Cooler Coolant Supply Lines Studbolt | 25 | 18 | - | |
| Oil Cooler Coolant Supply Lines Bolt | 25 | 18 | - | |
| Oil Filter | Refer to INSTALLATION . | |||
| Oil Jet Bolt | 10 | - | 89 | |
| Oil Level Indicator Tube to Cylinder Block | 22 | 16 | - | |
| Resonator Bolt | 9 | - | 80 | |
| Oil Pan to Block | ||||
| M6 Bolts | 10 | - | 89 | |
| M8 Bolts | 23 | 17 | - | |
| Oil Pan Drain Plug | 27 | 20 | - | |
| Oil Pressure Sensor | 48 | 35 | - | |
| Oil Temperature Sensor | 48 | 35 | - | |
| Oxygen Sensor | 50 | 37 | - | |
| Right Engine Mount to Frame Rail Bolts | 70 | 52 | - | |
| Right Engine Mount to Strut Tower | 65 | 48 | - | |
| Right Engine Mount to Timing Cover Bolts | 79 | 58 | - | |
| Starter Motor to Engine Block | 36 | 27 | - | |
| Tensioner to Accessory Drive Bracket | 26 | 19 | - | |
| Timing Chain Cover | ||||
| Cylinder Head Cover to Cylinder Head Bolts | 10 | - | 89 | |
| M6 Bolts | 9 | - | 80 | |
| M8 Bolts | 25 | 18 | - | |
| M10 Bolts | 65 | 48 | - | |
| Negative Battery Cable to Transmission Bolt | 22 | 16 | - | |
| Timing Chain Tensioner Assembly | 9 | - | 80 | |
| Timing Chain Guide M8 x 55 mm Bolts | 12 | 9 | - | |
| Timing Chain Tensioner Arm M8 x 40 mm Bolt | 28 | 21 | - | |
| Torque Strut (Rear Engine Mount) to Cradle Bolt and Nut | 110 | 81 | - | Do not reuse this fastener. If removed, a NEW fastener must be installed and tightened to specifications. |
| Torque Strut (Rear Engine Mount) to Transmission Bracket Bolt and Nut | 115 | 85 | - | |
| Torque Strut bracket to Cradle | 62 | 46 | - | |
| Transmission to Engine | 50 | 37 | - | |
| Vacuum Pump to Cylinder Head Bolts | 23 | 17 | - | |
| Water Inlet Tube to Cylinder Block Bolts | 24 | 18 | - | |
| Windage Tray to Block | 10 | - | 89 | |