Common Specs & Procedures
RENEGADE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 148 ft. lbs. (200 N.m) Do not reuse fastener. If removed, a new fastener must be installed and tightened to specifications. | ||
| Rear | 52 ft. lbs. + 47° (70 N.m + 47°) * NEW FASTENER: Do not reuse these fasteners. If removed, a new fastener must be installed and tightened to specifications. | ||
| Battery | TECHNICAL SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: MANUAL BLEEDING PROCEDURE
NOTE:
Bleeding procedure for Antilock Brakes is not available from the manufacturer.
|
||
| Disc Brakes | |||
| Service Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Base Brakes: TORQUE SPECIFICATIONS , Antilock Brakes: TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| 1.3L | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| 2.4L | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| 1.3L | |||
| Engine Coolant | 5.5 Quarts (5.2 Liters) MOPAR® Antifreeze/Coolant 10 Year/150, 000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032.. |
||
| Radiator Cap Pressure | The cap is designed to hold up to 20 psi. | ||
| Thermostat R & I | REMOVAL AND INSTALLATION . | ||
| Water Pump R & I | REMOVAL AND INSTALLATION . | ||
| 2.4L | |||
| Engine Coolant | 6.8 Quarts (6.5 Liters) MOPAR® Antifreeze/Coolant 10 Year/150, 000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032.. |
||
| Radiator Cap Pressure | The cap is designed to hold up to 20 psi. | ||
| Thermostat R & I | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| 1.3L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil Pressure | TECHNICAL SPECIFICATIONS | ||
| Overhaul | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.4L | |||
| Compression | Compression Pressure 1172 - 1551 kPa - 170 - 225 psi Max. Variation Between Cylinders 25%. | ||
| Oil pressure | At Curb Idle Speed. 25 kPa (4 psi min.) At 3000 RPM. 170-550 kPa (25 - 80 psi.) |
||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 1.3L | Refer to the appropriate tightening sequence INSTALLATION | ||
| 2.4L | 29 N.m + 51° - 21 Ft + 50° | ||
| Fuel System | |||
| Pressure Specification | |||
| 1.3L | The fuel pressure specification for all engines, including a Non SRT-4 is 407 kPa +/- 34 kPa (58 psi +/- 5 psi). SRT-4 fuel pressure specification is 552 kPa +/- 34 kPa (80 psi +/- 5 psi). | ||
| 2.4L | The fuel pressure specification for all engines, including a Non SRT-4 is 407 kPa +/- 34 kPa (58 psi +/- 5 psi). SRT-4 fuel pressure specification is 552 kPa +/- 34 kPa (80 psi +/- 5 psi). | ||
| Fuel Pressure Test Procedure | |||
| 1.3L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| 2.4L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | |||
| 1.3L | Fuel filters are integrated into the main fuel pump module. | ||
| 2.4L | Fuel filters are integrated into the main fuel pump module. | ||
| Fuel Filter R & I | |||
| 1.3L | REMOVAL AND INSTALLATION | ||
| 2.4L | REMOVAL AND INSTALLATION | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 1.3L | |||
| Type | Information is not available from the manufacturer. | ||
| Gap | Information is not available from the manufacturer. | ||
| Torque | Information is not available from the manufacturer. | ||
| 2.4L | |||
| Type | Information is not available from the manufacturer. | ||
| Gap | Information is not available from the manufacturer. | ||
| Torque | 27 N.m - 20 Ft | ||
| Starting | |||
| Starter | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Front: TORQUE SPECIFICATIONS , Rear: TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 89 ft. lbs. (120 N.m) | ||