Section 5 ((Electronic Power Steering (EPS) Module - Electrical Diagnostics))
WARNING: This page is about a different car, the 2015 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Code Index
- Diagnosis And Testing
- C1000-68-Electric Power Steering (EPS) Over Temperature - Event Information
- C1000-98-EPS Over Temperature - Component Or System Over Temperature
- C1001-48-Internal Error - Supervision Software Failure
- C1001-49-EPS - Internal Electronic Failure
- C1002-25-Absolute Position Sensor - Signal Shape/Waveform Failure
- C1003-86-Vehicle Speed VSO Signal - Signal Invalid
- C1004-49-Torque Sensor Error - Internal Electronic Failure
- C1005-68-Electric Power Steering (EPS) Lamp Failure - Event Information
- C1005-86-Status Lamp Failure BCM - Signal Invalid
- C1006-01-Electric Motor - General Electrical Failure
- C1007-87-C1 IGW1 Message From Body Control Module (BCM) Is Missing - Missing Message
- C1008-54-Absolute Steering Position Sensor Not Calibrated- Missing Calibration
- C1009-09-EPS Permanent Fault - Component Failure
- C100A-61-Message Counter From Brake2 Message - Signal Calculation Failure
- C100A-86-Message Counter From Brake2 Message - Signal Invalid
- C100B-86-Max Time Torque Request From Brake System Module (BSM) - Signal Invalid
- C100C-86-Max Time Torque Request From Abs - Signal Invalid
- C100D-86-Max Value Or EXOR From Brake System Module (BSM) - Signal Invalid
- C100E-86-Torque Overlay Controller (TOC) Status Error From BSM - Signal Invalid
- C100F-08-Brake2 Message From Brake System Module (BSM) - Bus Signal/Message Failure
- C100F-86-TOC Status Error From Abs - Signal Invalid
- C100F-87-Brake2 Message From Brake System Module (BSM) - Missing Message
- C1010-86-Max Rate From Brake System Module (BSM) - Signal Invalid
- C1011-85-Max Value From Half Module (Half) - Signal Invalid
- C1012-85-Max Rate From Half Module (Half) - Signal Above Allowable Range
- C1013-49-Half Module Faulty - Internal Electronic Failure
- C1013-86-Half Module Faulty - Signal Invalid
- C1014-86-Parking Aid Module (PAM) Incorrect Deactivation - Signal Invalid
- C1015-92-Parking Aid Module (PAM) - Performance Or Incorrect Operation
- C1016-85-Parking Aid Module (PAM) - Signal Above Allowable Range
- C1017-86-DRIVESTYLE STS Signal From Body2 Message Not Valid - Signal Invalid
- C1018-68-VIN Message From Body Control Module (BCM) Is Missing - Event Information
- C1019-68-Vehicle Standstill STS Signal From Brake4 Message Is Missing - Event Information
- C1020-68-Wheel Info Message Is Missing - Event Information
- C1200-16-Battery Voltage - Below Threshold
- C1200-17-Battery Voltage - Above Threshold
- C1200-1C-Battery Voltage - Circuit Voltage Out Of Range
- C1200-1F-Battery Voltage - Circuit Intermittent
- C1214-62-CONF Data Code Request Message - Signal Compare Failure
- C1214-87-CONF Data Code Request Message - Missing Message
- C1230-51-BCM PROXI Not Programmed - Not Programmed
- U1001-87-Can C Bus - Missing Message
- U1001-88-Can C Bus - Bus Off
- U1700-86-BCM Body Computer Module - Signal Invalid
- U1700-87 Body Computer Module (BCM) - Missing Message
- U1701-86-Engine Control Module (ECM) - Signal Invalid
- U1701-87-Engine Control Module (ECM) - Missing Message
- U1703-87-Instrument Panel Cluster (IPC) - Missing Message
- U1706-87-Brake System Module (BSM) - Missing Message
- U1724-87-Parking Aid Module (PAM) - Missing Message
- U1730-87-Haptic Lane Feedback Module (Half) - Missing Message
- U1932-86-Operational Mode STS Signal From BCM Command Message Not Valid - Signal Invalid
- U1950-83-Message Counter/CRC Fault On BCM Command Message - Value Of Signal Protection Calculation Incorrect
- U1952-83-Message Counter/CRC Fault On Brake1 Message - Value Of Signal Protection Calculation Incorrect
- U1954-83-Cyclic Redundancy Check (CRC) From Brake2 Message - Value Of Signal Protection Calculation Incorrect
- U1960-83-Message Counter/CRC Fault On Engine1 Message - Value Of Signal Protection Calculation Incorrect
- U1968-83-Message Counter/CRC Fault On Half Steer Control Message - Value Of Signal Protection Calculation Incorrect
- U1976-83-Message Counter/CRC Fault On SPM Steer Control Message - Value Of Signal Protection Calculation Incorrect
- U1982-83-Message Counter/CRC Fault On Wheel Info Message - Value Of Signal Protection Calculation Incorrect
- Standard Procedure