LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2015 >> Cherokee Limited, 3.2L Eng VIN S, AWD, Automatic T/Case Control >> Repair and Diagnosis >> Transmission >> Transmission Control Systems >> 948TE Automatic Transmission (Service Information) >> Installation >> Diesel

948TE Automatic Transmission (Service Information): Installation: Diesel

WARNING:

Hoisting and jack lift points provided in this service information are for a complete vehicle. When the transaxle is removed, the center of gravity will shift to the rear of the vehicle, possibly creating an unstable condition. Place safety stands under the rear frame rails behind the rear axle to stabilize the vehicle. Personal injury may result if safety stands are not used.

NOTE:

If installing a new transmission, remove the shipping cap from the vent.

  1. While guiding the transmission past obstacles, raise the transmission upward until the engine and the transmission are in line.
  2. Push the bell housing against the engine block until the guide pins engage.
    Fig 1: Transmission Bolt
    GC0162310Courtesy of CHRYSLER GROUP, LLC
  3. Install the front engine to transmission bolt (1) hand tight.
    Fig 2: Transmission Bolt
    GC0162267Courtesy of CHRYSLER GROUP, LLC
  4. Install the rear engine to transmission bolt (1) hand tight.
    Fig 3: Engine Oil Pan, Bolts, Transmission Jack, High Stand & Wooden Block
    GC0162305Courtesy of CHRYSLER GROUP, LLC
  5. Install the bolts (2) attaching the transmission to engine oil pan hand tight.
  6. Tighten the installed bolts to SPECIFICATIONS .
  7. Install the left lower load beam. Refer to LOAD BEAM, LOWER, INSTALLATION .
  8. Install the rear engine mount. Refer to
    Fig 4: Wooden Block Placed Between Transmission And Frame Rail
    GC0159581Courtesy of CHRYSLER GROUP, LLC
  9. Place a wooden block (1) between the load beam and the transmission end cover.
    Fig 5: Transmission Cooler Lines
    GC0159945Courtesy of CHRYSLER GROUP, LLC
  10. Engage the quick couplings to hold the cooler lines to the transmission.
    Fig 6: Torque Converter Bolts
    GC0162290Courtesy of CHRYSLER GROUP, LLC
    CAUTION:

    It is essential that correct length bolts be used to attach the converter to the driveplate. Failure to follow this caution may result in transmission damage.

  11. Through the starter opening, install NEW  bolts (1) to hold the flexplate to the torque converter and tighten to SPECIFICATIONS .
  12. Install the starter. Refer to STARTER, INSTALLATION .
    Fig 7: Dust Cover Bolt & Cover
    GC0162249Courtesy of CHRYSLER GROUP, LLC
  13. Install the dust cover (1) and tighten bolt (2) to SPECIFICATIONS .
    Fig 8: Transmission End Cover Ground Cable
    GC0159835Courtesy of CHRYSLER GROUP, LLC
  14. Install the ground cable (1) to the transmission and tighten to SPECIFICATIONS .
  15. Install the left engine mount adapter to the transmission and tighten to SPECIFICATIONS .
  16. Install the left side engine mount. Refer to .
  17. Install upper bolts to hold the transmission to the engine block and tighten to SPECIFICATIONS .
    Fig 9: Transmission Valve Body Solenoid Connector
    GC0159235Courtesy of CHRYSLER GROUP, LLC
  18. Connect the transmission solenoid connector (1).
    Fig 10: View Of Shift Cable Housing & Mount Bracket
    GC0160099Courtesy of CHRYSLER GROUP, LLC
  19. Place the shift cable (2) in position on the mount bracket (2).
  20. Press the shift cable housing (2) into the mount bracket (1) on the transmission.
    Fig 11: View Of Ground Cable & Shift Cable
    GC0159736Courtesy of CHRYSLER GROUP, LLC
  21. Snap the shift cable end (2) in position on the manual lever on the transmission.
    Fig 12: Ground Cable At Top Transmission
    GC0159644Courtesy of CHRYSLER GROUP, LLC
  22. Install the ground cable to the top of the transmission and tighten bolt to SPECIFICATIONS .
    Fig 13: Identifying Wire Connector Lock To TCM
    GC0159257Courtesy of CHRYSLER GROUP, LLC
  23. Engage the wire connector (1) into the TCM connector.
  24. Close the lock on the TCM connector (1).
  25. If equipped, install the Power Transfer Unit (PTU). Refer to INSTALLATION .
  26. Install the left and right half shafts. Refer to INSTALLATION or INSTALLATION .
  27. Install the Diesel Particulate Filter (DPF) bracket onto engine block and tighten bolts to SPECIFICATIONS .
  28. Install the DPF. Refer to FILTER, DIESEL PARTICULATE, INSTALLATION .
  29. Install the Charge Air Cooler (CAC) hose.
  30. Install the battery tray. Refer to TRAY, BATTERY, INSTALLATION .
  31. Install the belly pan. Refer to BELLY PAN, INSTALLATION .
  32. Install new rivets at the lower outboard front fascia to right front splash shield.
  33. Install the left front fender splash shield. Refer to SHIELD, SPLASH, FRONT WHEELHOUSE, INSTALLATION .
  34. Install the front wheels. Refer to INSTALLATION .
  35. Lower the vehicle.
  36. Install the battery. Refer to BATTERY, INSTALLATION .
  37. Fill the transmission to the proper level with the specified fluid.
  38. If transmission is replaced, program the Vehicle Identification Number (VIN) into the Transmission Control Module (TCM).
    NOTE:

    Note; only perform the Valve Body Solenoid Learn procedure if the valve body and/or the TCM was replaced during a repair. Do not perform this procedure if the repair did not require the valve body and/or TCM to be replaced. Do not perform this procedure if the transmission is being replaced. 

  39. If valve body or the TCM was replaced, perform Valve Body Solenoid Learn procedure.
  40. If transmission is replaced or internal repairs were made, perform Transmission Verification Test-948TE. Refer to STANDARD PROCEDURE .
  41. Road test the vehicle to verify the repair.
scientia non olet · About LEMON Manuals