Diagnostic Test

TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
3. Operate the Mirror Switch in all directions several times.
4. Cycle the ignition from on to off 3 times.
5. Turn the ignition on.
6. With the scan tool, read DTCs.
  Does the scan tool display: B1D27-PASSENGER MIRROR MOTOR COMMON CONTROL CIRCUIT LOW?
  
  Yes
  - Go to step 2
  No
  - The conditions that caused this code to set are not present at this time. Using the SYSTEM WIRING DIAGRAMS as a guide, inspect the wiring and connectors.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
TEST FOR A SHORTED OUTSIDE REARVIEW MIRROR

Fig 1: Testing For A Shorted Outside Rearview Mirror
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Passenger Outside Rearview Mirror connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Operate the Mirror Switch in all directions several times.
6. Cycle the ignition from on to off 3 times.
7. Turn the ignition on.
8. With the scan tool, read DTCs.
  Does the scan tool display: B1D27-PASSENGER MIRROR MOTOR COMMON CONTROL CIRCUIT LOW?
  
  Yes
  - Go to step 3
  No
  - Replace the Outside Rearview Mirror in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
CHECK THE (P70) PASSENGER MIRROR COMMON DRIVER CIRCUIT FOR A SHORT TO GROUND

Fig 2: Checking Passenger Mirror Common Driver Circuit For A Short To Ground
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Passenger Door Module C2 connector.
3. Measure the resistance between ground and the (P70) Passenger Mirror Common Driver circuit in the Passenger Door Module C2 connector.
  Is the resistance below 10k ohms?
  
  Yes
  - Repair the (P70) Passenger Mirror Common Driver circuit for a short to ground.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Go to step 4
CHECK THE (P70) PASSENGER MIRROR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (P66) PASSENGER MIRROR SENSOR GROUND CIRCUIT

Fig 3: Checking Passenger Mirror Common Driver Circuit For A Short To Passenger Mirror Sensor Ground Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (P70) Passenger Mirror Common Driver circuit and the (P66) Passenger Mirror Sensor Ground circuit in the Passenger Door Module C2 connector.
  Is the resistance below 10k ohms?
  
  Yes
  - Repair the (P70) Passenger Mirror Common Driver circuit for a short to the (P66) Passenger Mirror Sensor Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Go to step 5
CHECK THE (P70) PASSENGER MIRROR COMMON DRIVER CIRCUIT FOR A SHORT TO THE (C917) PASSENGER MIRROR HEATER RETURN CIRCUIT

Fig 4: Checking Passenger Mirror Common Driver Circuit For A Short To Passenger Mirror Heater Return Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (P70) Passenger Mirror Common Driver circuit and the (C917) Passenger Mirror Heater Return circuit in the Passenger Door Module C2 connector.
  Is the resistance below 10k ohms?
  
  Yes
  - Repair the (P70) Passenger Mirror Common Driver circuit for a short to the (C917) Passenger Mirror Heater Return circuit.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Replace the Passenger Door Module in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .