Diagnostic Test

DTC PRESENT
1. With the scan tool, record and erase DTCs.
2. Turn the ignition off, wait 10 seconds, then turn the ignition on.
3. Operate the power liftgate several times if possible.
4. With the scan tool, read DTCs.
5. If the B210D-BATTERY VOLTAGE LOW DTC is present, repair that code before proceeding.
  Does the scan tool display B1984-POWER LIFTGATE LATCH CONTROL 2 CIRCUIT LOW?
  
  Yes
  - Go to step 2
  No
  - Using the SYSTEM WIRING DIAGRAMS as a guide, inspect the wiring and connectors for an intermittent condition. Operate the liftgate several times and check for any binding conditions in the latch assembly.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
BINDING LIFTGATE LATCH
1. Examine the liftgate for proper alignment, worn or binding hinges, latch alignment or anything that would cause an obstruction to proper operation.
2. With an open liftgate, manually close the latch and open it with the handle switch several times.
  Were there any mechanical problems found?
  
  Yes
  - Refer to Service information for the related symptom(s).
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Go to step 3
CHECK THE (Q85) LIFTGATE LATCH RELEASE DRIVER CIRCUIT FOR A SHORT TO THE (Q901) LOGIC GROUND CIRCUIT

Fig 1: Checking Liftgate Latch Release Driver Circuit For A Short To Logic Ground
Courtesy of CHRYSLER LLC
1. Disconnect the Power Liftgate Latch harness connector.
2. Measure the resistance between the (Q901) Logic Ground circuit and the (Q85) Liftgate Latch Release Driver circuit in the Power Liftgate Latch harness connector.
3. Wiggle the harness and check for an intermittent short circuit condition.
  Is the resistance below 100.0 ohms?
  
  Yes
  - Go to step 6
  No
  - Go to step 4
CHECK THE (Q84) LIFTGATE LATCH CINCH DRIVER CIRCUIT FOR A SHORT TO THE (Q901) LOGIC GROUND CIRCUIT

Fig 2: Checking Liftgate Latch Cinch Driver Circuit For A Short To Logic Ground
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (Q901) Logic Ground circuit and the (Q84) Liftgate Latch Cinch Driver circuit in the Power Liftgate Latch harness connector.
2. Wiggle the harness and check for an intermittent short circuit condition.
  Is the resistance below 100.0 ohms?
  
  Yes
  - Go to step 6
  No
  - Go to step 5
CHECK THE (Q84) LIFTGATE LATCH CINCH DRIVER CIRCUIT FOR A SHORT TO THE (Q85) LIFTGATE LATCH RELEASE DRIVER CIRCUIT

Fig 3: Checking Liftgate Latch Circuit Open
Courtesy of CHRYSLER LLC
1. Disconnect the Power Liftgate Module C2 harness connector.
2. Measure the resistance between the (Q84) Liftgate Latch Cinch Driver circuit and the (Q85) Liftgate Latch Release Driver circuit in the Power Liftgate Module C2 harness connector.
  Is the resistance below 10000.0 ohms?
  
  Yes
  - Repair the (Q84) Liftgate Latch Cinch Driver circuit for a short to the (Q85) Liftgate Latch Release Driver Circuit.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Replace the Power Liftgate Latch assembly in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
CHECK THE (Q85) LIFTGATE LATCH RELEASE DRIVER CIRCUIT FOR A SHORT TO GROUND

Fig 4: Checking Liftgate Latch Release Driver Circuit For A Short To Ground
Courtesy of CHRYSLER LLC
1. Disconnect the Power Liftgate Module C2 harness connector.
2. Measure the resistance between ground and the (Q85) Liftgate Latch Release Driver circuit.
3. Wiggle the harness and check for an intermittent short circuit condition.
  Is the resistance below 10000.0 ohms?
  
  Yes
  - Repair the (Q85) Liftgate Latch Release Driver circuit for a short to ground.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Go to step 7
CHECK THE (Q84) LIFTGATE LATCH CINCH DRIVER CIRCUIT FOR A SHORT TO GROUND

Fig 5: Checking Liftgate Latch Cinch Driver Circuit For A Short To Ground
Courtesy of CHRYSLER LLC
1. Measure the resistance between ground and the (Q84) Liftgate Latch Cinch Driver circuit.
2. Wiggle the harness and check for an intermittent short circuit condition.
  Is the resistance below 10000.0 ohms?
  
  Yes
  - Repair the (Q84) Liftgate Latch Cinch Driver circuit for a short to ground.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .
  No
  - Replace the Power Liftgate Module in accordance with Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE, Front Control (FCM) - Standard Procedure .