LEMON Manuals: Even more car manuals for everyone
Home >> Isuzu >> 2007 >> Ascender RWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System & Fuel System - 4.2L - DTC P0135 To DTC P0420 >> DTC P0365 >> Test Description

Test Description

The number below refers to the step number on the diagnostic table.

  1. 7:  This step tests the CMP sensor signal circuit. If the CMP Active Counter counts when the circuit is touched, it is OK.
DTC P0365

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 Attempt to start the engine.
Does the engine start and run?		 - Go to Step 3  Go to Step 8 
3
  1. Start the engine.
  2. Observe the CMP Active Counter parameter with a scan tool.
Does the scan tool parameter increment?		 - Go to Step 4  Go to Step 5 
4
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 5  Go to Diagnostic Aids 
5
  1. Turn OFF the ignition.
  2. Disconnect the camshaft position (CMP) sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the 12-volt reference circuit with a test lamp that is connected to a good ground. Refer to Probing Electrical Connectors .
Does the test lamp illuminate?		 - Go to Step 6  Go to Step 8 
6
  1. Turn OFF the ignition.
  2. Jumper the CMP circuits from the CMP sensor to the CMP sensor harness connector. Refer to Using Connector Test Adapters .
  3. Turn ON the ignition with the engine OFF.
  4. Measure the Voltage Drop from the low reference circuit of the CMP sensor to a good ground with a DMM. Refer to Circuit Testing .
Is the voltage more than the specified value?		 0.2 V Go to Step 9  Go to Step 7 
7 
  1. Turn OFF the ignition.
  2. Remove the jumper wires from the CMP circuits.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the CMP Active Counter parameter with the scan tool.
  5. Momentarily and repeatedly probe the signal circuit of the CMP sensor with a test lamp that is connected to battery voltage.
Does the CMP Active Counter parameter count each time the test lamp contacts the circuit?		 - Go to Step 11  Go to Step 10 
8 Test the 12-volt reference circuit for the following conditions:
  • An open
  • High resistance
  • A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 16  Go to Step 12 
9 Test the low reference circuit for the following conditions:
  • An open
  • High resistance

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 16  Go to Step 12 
10 Test the signal circuit for the following conditions:
  • An open
  • A short to ground
  • A short to voltage

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 16  Go to Step 12 
11 Test for an intermittent and for a poor connection at the CMP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 16  Go to Step 13 
12 Test for an intermittent and for a poor connection at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 16  Go to Step 15 
13
  1. Remove the CMP sensor.
  2. Visually inspect the CMP sensor for the following conditions:
    • Physical damage
    • Loose or improper installation
Did you find and correct the condition?		 - Go to Step 16  Go to Step 14 
14 Replace the CMP sensor. Refer to Camshaft Position Sensor Replacement .
Did you complete the replacement?		 - Go to Step 16  -
15 Replace the PCM. Refer to Control Module References for replacement, setup and programming.
Did you complete the replacement?		 - Go to Step 16  -
16
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 17 
17 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals