LEMON Manuals: Even more car manuals for everyone
Home >> Isuzu >> 2000 >> Rodeo S, 2.2 D >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics - Introduction >> On-Board Diagnostic II (OBD-II) System Check >> Amigo/Rodeo 2.2L & VEHICROSS

Amigo/Rodeo 2.2L & VEHICROSS

NOTE: Perform all voltage tests with a Digital Volt-Ohmmeter (DVOM) with a minimum 10-megohm impedance, unless stated otherwise in test procedure.
  1. Turn ignition on with engine off. Verify Malfunction Indicator Light (MIL) is on. If MIL is on, go to next step. If MIL is not on, go to MALFUNCTION INDICATOR LIGHT (MIL) INOPERATIVE in SELF-DIAGNOSTICS - 3.2L & 3.5L article.
  2. Turn ignition off. Install TECH II scan tool. Turn ignition on. If scan tool displays PCM data, go to next step. If scan tool does not display PCM data, verify scan tool is properly installed. If scan tool is properly installed, go to step  8.
  3. Using scan tool, command MIL OFF. If MIL turns off, go to next step. If MIL does not turn off, go to MIL ON STEADY in SELF-DIAGNOSTICS - 3.2L & 3.5L article.
  4. Start engine. If engine starts and continues to run, go to next step. If engine will not run, go to ENGINE CRANKS BUT WILL NOT RUN under NO START DIAGNOSIS in BASIC DIAGNOSTIC PROCEDURES article.
  5. Using scan tool, check if any DTCs have been set. If any DTCs are set, go to next step. If no DTCs are set, go to step  7.
  6. If 2 or more of the following DTCs are stored, go to MULTIPLE PCM INFORMATION SENSOR DTCS SET under SELF-DIAGNOSTIC SYSTEM in SELF-DIAGNOSTICS - 3.2L & 3.5L article. If a single DTC is stored, go to appropriate DTC test under DIAGNOSTIC TESTS in appropriate SELF-DIAGNOSTICS article.
    • P0107
    • P0108
    • P0113
    • P0118
    • P0122
    • P0123
    • P0712
  7. Compare PCM data values displayed to typical engine scan data values. See appropriate SCAN TOOL DATA VALUES table under PIN VOLTAGE (VALUE) TESTS in PIN VOLTAGE CHARTS article. If values displayed are normal or close to typical values, OBD-II system check is complete. If driveability problem still exists, go to TROUBLE SHOOTING - NO CODES article. If values are not correct, go to appropriate component test in SYSTEM & COMPONENT TESTING article.
  8. Turn ignition off. Disconnect PCM connectors. Turn ignition on with engine off. Check for open or short in class 2 data circuit (Black wire on Amigo and Rodeo; Orange/Green wire on VehiCROSS) between Data Link Connector (DLC) terminal No. 2 and PCM 32-pin Red connector terminal B13. Also check for open or short in ignition feed circuit (Green/Yellow wire on Amigo and Rodeo; Green/White wire on VehiCROSS) between DLC terminal No. 16 and fuse box. Also check for open in ground circuit (Black/Blue wire) to DLC terminal No. 4. If problem is found, repair as necessary and return to step  2. If no problem is found, go to next step.
  9. Attempt to reprogram EEPROM. See PROGRAMMING under SELF-DIAGNOSTIC SYSTEM in SELF-DIAGNOSTICS - 3.2L & 3.5L article. Programming PCM/EEPROM requires the use of a scan tool and special manufacturer equipment. Attempt to display PCM data on scan tool. If data is now displayed, return to step  2. If data is not displayed, go to next step.
  10. Replace and reprogram PCM. After repair, return to step  2.
scientia non olet · About LEMON Manuals