CONSULT Function
FUNCTION
CONSULT can display each diagnostic item using the diagnostic test modes as follows.
| Diagnostic test mode | Function |
|---|---|
| ECU Identification | Transfer control unit part number can be read. |
| Self Diagnostic Result | Self-diagnostic results can be read and erased quickly. * |
| Data Monitor | Input/Output data in the transfer control unit can be read. |
| Work Support | This mode enables a technician to adjust some devices faster and more accurately by following the indications on the CONSULT |
*: The following diagnosis information is erased by erasing.
- DTC
ECU IDENTIFICATION
Transfer control unit part number can be read.
SELF DIAGNOSTIC RESULT
Refer to DTC Index . When "0" is displayed on self-diagnosis result.
- The system is presently malfunctioning.
When except "0" is displayed on self-diagnosis result.
- System malfunction in the past is detected, but the system is presently normal.NOTE: Each time when ignition switch is turned OFF to ON, numerical number increases in 1→2→3..110→111.
When the operation number of times exceeds 111, the number do not increase and "111" is displayed until self-diagnosis is erased *.
*: For "U1000" and "U1010", the maximum value is "39".
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
X: Applicable
| Monitor item (Unit) | SELECT MONITOR ITEM | Remarks | |
|---|---|---|---|
| ECU INPUT SIGNALS | MAIN SIGNALS | ||
| 4WD MODE [BOTNG/SWTNG/4L/4H/AUTO] | X | Control status of 4WD mode is displayed. | |
| 2WD SW [On/Off] | X | 4WD shift switch (2WD) is not equipped, but it is displayed. | |
| AUTO SW [On/Off] | X | 4WD shift switch signal (AUTO) is displayed. | |
| 4H SW [On/Off] | X | 4WD shift switch signal (4H) is displayed. | |
| 4L SW [On/Off] | X | 4WD shift switch signal (4L) is displayed. | |
| T/M RANGE [D/N/R/P] | X | A/T shift selector position via CAN communication line is displayed. | |
| N RANGESW [On/Off] | X | A/T shift selector position (N) via CAN communication line is displayed. | |
| R RANGE SW [On/Off] | X | A/T shift selector position (R) via CAN communication line is displayed. | |
| ING SW [On/Off] | X | Ignition switch status is displayed. | |
| TCS OPER [On/Off] | X | TCS operation status via CAN communication line is displayed. | |
| VDC OPER [On/Off] | X | VDC operation status via CAN communication line is displayed. | |
| ABS OPER [On/Off] | X | ABS operation status via CAN communication line is displayed. | |
| SAND MODE IND [On/Off] | This indicator is not equipped, but it is displayed. | ||
| ROCK MODE IND [On/Off] | This indicator is not equipped, but it is displayed. | ||
| SNOW MODE IND [On/Off] | This indicator is not equipped, but it is displayed. | ||
| ONROAD MODE IND [On/Off] | This indicator is not equipped, but it is displayed. | ||
| SAND MODE SW [On/Off] | X | This switch is not equipped, but it is displayed. | |
| ROCK MODE SW [On/Off] | X | This switch is not equipped, but it is displayed. | |
| SNOW MODE SW [On/Off] | X | This switch is not equipped, but it is displayed. | |
| ONROAD MODE SW [On/Off] | X | This switch is not equipped, but it is displayed. | |
| HI/LO POSI SEN 3 [On/Off] | X | Transfer Hi-Lo position sensor (3) status is displayed. | |
| HI/LO POSI SEN 1 [On/Off] | X | Transfer Hi-Lo position sensor (1) status is displayed. | |
| LOCK POSI SEN [OPEN/LOCK/BAT/UNLEAN/HI TEMP/ERROR/GND] | X | Transfer lock position sensor signal is displayed. | |
| ATP IND [On/Off] | Control status of ATP warning lamp is displayed. | ||
| 4WD FAILLAMP [On/Off] | X | Control status of ATP warning lamp is displayed. | |
| 4WD MODE IND [4L/LOCK/AUTO] | X | Control status of 4WD mode indicator lamp is displayed. (LOCK means 4H of 4WD mode) |
|
| MOTOR DRIVE B [HI/LO/PWM] | X | Driving status of transfer motor is displayed. (Reverse side) | |
| MOTOR DRIVE A [HI/LO/PWM] | X | Driving status of transfer motor is displayed. (Drive side) | |
| FLUID TEMP SEN [V] | X | Temperature of transfer fluid is displayed. | |
| MOTOR TEMP [V] | X | Temperature of transfer motor is displayed. | |
| C/U POWER SUP [V] | X | Power supply voltage value of transfer control unit is displayed. | |
| MOTOR POWER SUP [V] | X | Power supply voltage value of transfer motor unit is displayed. | |
| ROTARY POSI SEN [%] | X | Transfer rotary position sensor signal is displayed. | |
| THRTL POSI SEN [%] | X | X | Throttle opening status via CAN communication line is displayed. |
| AT R SPEED [km/h] | X | Output shaft revolution speed via CAN communication line is displayed. | |
| T/M GEAR [0 - 7] | X | Current transmission gear via CAN communication line is displayed. | |
| COMPR VHCL SPEED [km/h] | X | Vehicle speed calculated by transfer control unit is displayed. | |
| VHCL/S SEN-FR [km/h] | X | Wheel speed (front) average calculated by transfer control. | |
| VHCL/S SEN-RR [km/h] | X | Wheel speed (rear) average calculated by transfer control. | |
| ENG SPEED [RPM] | X | Engine status via CAN communication line is displayed. | |
| INTERNL SPEED SEN [count] | X | Transfer internal speed sensor status is displayed. | |
| TRANSFER TORQUE [Nm] | X | Commanded transfer communication torque is displayed. | |
| UNIT PARAMETER [A1 - A9, B1 - B9, C1 - C9, D1 - D9, E1 - E9, F1 - F9, G1 - G9, H1 - H9, J1 - J9] | Unit parameter of transfer recognized by transfer control unit is displayed. | ||
WORK SUPPORT
| Function | Description |
|---|---|
| UNIT CHARACTERISTIC WRITE | Writes the unit parameter of transfer to transfer control unit. |
| START CALIBRATION | Perform initial calibration of transfer control unit. |
| LOCK SLEEVE SENSOR * INITIALIZE | Format learning the transfer lock position sensor written to transfer control unit. |
| LOCK SLEEVE SENSOR * LEARNING | Perform learning the transfer lock position sensor. |
| OIL DETERIORATION INFO RESET | Format the transfer fluid viscosity written to transfer control unit. |
*: "LOCK SLEEVE SENSOR" means transfer lock position sensor.