Confirmation Procedure

PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1. Start engine and warm it up to normal operating temperature.
2. Let engine idle for 2 minutes.
3. Check 1st trip DTC.
Is DTC P2252 detected?

YES

Refer to DTC Diagnosis Procedure .

NO

With CONSULT: GO TO 3.

NO

Without CONSULT: GO TO 7.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
With CONSULT
1. Start engine and warm it up to normal operating temperature.
2. On CONSULT screen, select "ENGINE">>"Data Monitor">>"A/F SEN1 (B1)" or "A/F SEN1 (B2)".
3. Check "A/F SEN1 (B1)" or "A/F SEN1 (B2)" indication.
Does the indication fluctuate around 2.2 V?

YES

GO TO 4.

NO

Refer to DTC Diagnosis Procedure .

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-I

With CONSULT

On CONSULT screen, select "ENGINE">>"DTC Work Support">>"A/F SEN1">>"A/F SEN1 (B1) P1276" (for DTC P2252).
Touch "START".

When the following conditions are met, "TESTING" will be displayed on the CONSULT screen.

ENG SPEED	1, 000 - 3, 200 rpm
VHCL SPEED SE	More than 64 km/h (40 mph)
B/FUEL SCHDL	1.0 - 8.0 msec
Selector lever	D position

If "TESTING" is not displayed after 20 seconds, retry from step 2.

CAUTION: Always drive vehicle at a safe speed.

Is "TESTING" displayed on CONSULT screen?

YES

GO TO 5.

Check A/F sensor 1 function again. GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-II
Release accelerator pedal fully.

NOTE: Never apply brake when releasing the accelerator pedal.

Which does "TESTING" change to?

COMPLETED

GO TO 6.

OUT OF CONDITION

Retry DTC CONFIRMATION PROCEDURE. GO TO 4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-III
Touch "SELF-DIAG RESULT".

Is "OK" displayed on CONSULT screen?

YES

To check malfunction symptom before repair: Refer to Inspection .

YES

Confirmation after repair: INSPECTION END

NO

Refer to DTC Diagnosis Procedure .
PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
NOTE: Use component function check to check the overall function of the A/F sensor 1 circuit. During this check, a 1st trip DTC might not be confirmed.

With GST
1. Start engine and warm it up to normal operating temperature.
2. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in the suitable gear position.
3. Shift the selector lever to D position, then release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (30 MPH).
  CAUTION: Always drive vehicle at a safe speed.
  
  NOTE: Never apply brake when releasing the accelerator pedal.
4. Repeat steps 2 and 3 for five times.
5. Stop the vehicle and turn ignition switch OFF.
6. Turn ignition switch ON.
7. Turn ignition switch OFF and wait at least 10 seconds.
8. Restart engine.
9. Repeat steps 2 and 3 for five times.
10. Stop the vehicle and connect GST to the vehicle.
11. Check 1st trip DTC.
Is DTC P2252 detected?

YES

Refer to DTC Diagnosis Procedure .

NO

To check malfunction symptom before repair: Refer to Inspection .

NO

Confirmation after repair: INSPECTION END