LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2018 >> QX30 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 94 (Active Lane Control) >> Active Lane Control >> Basic Inspection >> Camera Aiming Adjustment >> Work Procedure (Target Setting)

Work Procedure (Target Setting)

WARNING: This page is about a different car, the 2018 Infiniti Q60. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
  • Be sure to place the target correctly according to work procedures because the system may not operate normally.
  • Perform this operation in a horizontal position where there is a clear view for 5 m (16.4 ft) forward and 3 m (9.84 ft) wide.
  • Place the target in a well-lighted location. (Poor lighting may make it hard to adjust.)
  • The target may not be detected when there is a light source within 1.5 m (4.92 ft) from either side and within 1 m (3.28 ft) upward/downward from the target.
  • Check the location of the sun. (Sunlight should not shine directly on the front of the vehicle.)
  • The target may not be detected when there is the same pattern of black and white as the target when the pattern is within 1 m (3.28 ft) from either side and upward/downward position from the target. (It is desirable that the vehicle is positioned on the opposite side of a single-color wall.)
  1. TARGET SETTING 
    G09170562Courtesy of NISSAN NORTH AMERICA, INC.

    SYMBOL - SYMBOL (SYMBOL - SYMBOL )

    : 3850 mm (151.57 in)
    1. Lengthen straight a measuring tape as follows. And then fix it with tapes.
      • A measuring tape contacts with the side of the front left side tire from rear left side tire.
      • A measuring tape lengthens approximately 4 m (13.12 ft) or more from the front end of vehicle.
        NOTE: Use the steel tape measure which can measure 10m (32.81 ft) or more
    2. Mark point SYMBOL on a measuring tape. Hang a string with a cone from the fender so as to pass through the center of wheel, and then mark a point at the center of the lateral surface of the wheel.
      G09161974Courtesy of NISSAN NORTH AMERICA, INC.
    3. Mark point SYMBOL on a measuring tape at the positions 3850 mm (151.57 in) from point SYMBOL .
    4. Remove a measuring tape.
      CAUTION: Be careful so that a marking point is not changed.
    5. Lengthen straight a measuring tape as follows. And then fix it with tapes.
      • A measuring tape contacts with the side of the front right side tire from rear right side tire.
      • A measuring tape lengthens approximately 4 m (13.12 ft) or more from the front end of vehicle.
        NOTE: Use the steel tape measure which can measure 10m (32.81 ft) or more
    6. Mark point SYMBOL on a measuring tape. Hang a string with a cone from the fender so as to pass through the center of wheel, and then mark a point at the center of the lateral surface of the wheel.
      G09161975Courtesy of NISSAN NORTH AMERICA, INC.
    7. Mark point SYMBOL on a measuring tape at the positions 3850 mm (151.57 in) from point SYMBOL .
    8. Remove a measuring tape.
      CAUTION: Be careful so that a marking point is not changed.
    9. Lengthen straight a measuring tape passing through the points SYMBOL and SYMBOL on the front side of vehicle. And then fix it with tapes.
    10. Mark point SYMBOL at the center of point SYMBOL and SYMBOL on a measuring tape.
      CAUTION: Make sure that SYMBOL to SYMBOL is equal to SYMBOL to SYMBOL .
    11. Remove a measuring tape.
      CAUTION: Be careful so that a marking point is not changed.
    12. Position the center of the right target to point of SYMBOL .
      G09161976Courtesy of NISSAN NORTH AMERICA, INC.
      CAUTION:
      • Be sure to place the board that the cross of the target is horizontal and vertical.
      • Fix point SYMBOL with a cone that hung down from the right side target.

    Proceed to Work Procedure (Camera Aiming Adjustment) .

scientia non olet · About LEMON Manuals