LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2017 >> Q60 Base, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Transfer Case) >> Unit Disassembly And Assembly >> Front Case And Rear Case >> Disassembly And Assembly >> Disassembly

Disassembly And Assembly: Disassembly

WARNING: This page is about a different variant/trim than selected.
  1. Remove drain plug, filler plug and gaskets.
  2. Remove main shaft oil seal from front case, using oil seal remover (commercial service tool).
    CAUTION:

    Never damage the front case and main shaft.

  3. Remove front oil seal from front case, using oil seal remover (commercial service tool).
    CAUTION:

    Never damage the front case and front drive shaft.

  4. While holding companion flange with the flange wrench (commercial service tool), remove self-lock nut.
  5. Put a matching mark MARU-A-W on the end of main shaft. The mark should be in line with the mark MARU-B-W on the companion flange.
    G05727164Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    For the matching mark, use paint. Never damage main shaft.

  6. Remove companion flange with a puller (A) (commercial service tool).
    G05979357Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Never damage the companion flange.

  7. Remove rear oil seal from rear case with the puller (A) [SST: KV381054S0 (J-34286) ].
    G05979333Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Never damage the rear case.

  8. Remove spacer from main shaft.
  9. Remove front case and rear case fixing bolts, then remove harness bracket.
    G09160823Courtesy of NISSAN NORTH AMERICA, INC.
    Bolts symbol Quantity
    MARU-A-W 13
    MARU-T-W (TORX bolt) 2

    * : With harness bracket.

  10. Remove front case WHITE-1 from rear case by levering it up with a suitable tool.
    G05979360Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Never damage the mating surface.

  11. Remove snap ring WHITE-1 from front case.
    G05979361Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Never damage front case.

  12. Remove main shaft bearing from front case.
    CAUTION:

    Never use tools. Always remove by hand.

  13. Remove snap ring WHITE-1 from main shaft.
    G05979362Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Never damage main shaft.

  14. Remove spacer WHITE-1 and steel ball WHITE-2 from main shaft.
    G05979363Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Be careful not to drop the steel ball.

  15. Remove oil pump from main shaft.
  16. Remove drive chain and front drive shaft assembly.
    CAUTION:

    Never use tools. Always remove by hand.

  17. Remove transfer fluid temperature sensor bolt from rear case. And then, remove transfer fluid temperature sensor WHITE-1 .
    G06626629Courtesy of NISSAN NORTH AMERICA, INC.
  18. Remove oil cover WHITE-1 .
    G06626630Courtesy of NISSAN NORTH AMERICA, INC.
  19. Remove retainer from AWD solenoid harness connector.
  20. Remove AWD solenoid harness connector from rear case.
  21. Remove main shaft assembly from rear case with the drift (A) [SST: ST33052000 (-) ].
    G05979366Courtesy of NISSAN NORTH AMERICA, INC.
  22. Remove snap ring WHITE-1 from rear case.
    G05979367Courtesy of NISSAN NORTH AMERICA, INC.
  23. Remove rear bearing from rear case.
    CAUTION:

    Never use tools. Always remove by hand.

  24. Remove baffle plate WHITE-1 from rear case.
    G05979368Courtesy of NISSAN NORTH AMERICA, INC.
  25. Remove breather tube from rear case.
  26. Perform inspection after disassembly. Refer to INSPECTION .
scientia non olet · About LEMON Manuals