Values On The Diagnosis Tool
WARNING: This page is about a different variant/trim than selected.
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor item | Condition | Value/Status | |
|---|---|---|---|
| MAIN SW | Ignition switch ON | When MAIN switch is pressed | On |
| When MAIN switch is not pressed | Off | ||
| SET/COAST SW | Ignition switch ON | When SET/COAST switch is pressed | On |
| When SET/COAST switch is not pressed | Off | ||
| CANCEL SW | Ignition switch ON | When CANCEL switch is pressed | On |
| When CANCEL switch is not pressed | Off | ||
| RESUME/ACC SW | Ignition switch ON | When RESUME/ACCELERATE switch is pressed | On |
| When RESUME/ACCELERATE switch is not pressed | Off | ||
| DISTANCE SW | Ignition switch ON | When DISTANCE switch is pressed | On |
| When DISTANCE switch is not pressed | Off | ||
| CRUISE OPE | Drive the vehicle and activate the vehicle-to-vehicle distance control mode | When ICC system is controlling | On |
| When ICC system is not controlling | Off | ||
| BRAKE SW | Ignition switch ON | When brake pedal is depressed | Off |
| When brake pedal is not depressed | On | ||
| STOP LAMP SW | Ignition switch ON | When brake pedal is depressed | On |
| When brake pedal is not depressed | Off | ||
| IDLE SW | READY state | Idling | On |
| Except idling (depress accelerator pedal) | Off | ||
| SET DISTANCE |
|
When set to "long" | Long |
| When set to "middle" | Mid | ||
| When set to "short" | Short | ||
| CRUISE LAMP | Set the vehicle to READY and press MAIN switch | ICC system ON (MAIN switch indicator ON) |
On |
| ICC system OFF (MAIN switch indicator OFF) |
Off | ||
| OWN VHCL |
NOTE:
The item is indicated, but not monitored |
Off | |
| VHCL AHEAD | Drive the vehicle and activate the vehicle-to-vehicle distance control mode | When a vehicle ahead is detected (vehicle ahead detection indicator ON) | On |
| When a vehicle ahead is not detected (vehicle ahead detection indicator OFF) | Off | ||
| ICC WARNING | Set the vehicle to READY and press MAIN switch | When ICC system is malfunctioning (ICC system warning ON) |
On |
| When ICC system is normal (ICC system warning OFF) |
Off | ||
| VHCL SPEED SE | While driving | Displays the vehicle speed calculated by ADAS control unit | |
| SET VHCL SPD | While driving | When vehicle speed is set | Displays the set vehicle speed |
| BUZZER O/P | READY state | When the buzzer of the following system operates
|
On |
When the buzzer of the following system not operates
|
Off | ||
| THRTL SENSOR |
NOTE:
The item is indicated, but not monitored |
0.0 | |
| ENGINE RPM | READY state | Equivalent to tachometer reading | |
| WIPER SW | Ignition switch ON | Wiper not operating | Off |
| Wiper LO operation | Low | ||
| Wiper HI operation | High | ||
| YAW RATE |
NOTE:
The item is indicated, but not monitored |
0.0 | |
| BA WARNING | READY state | FEB OFF indicator lamp ON
|
On |
FEB OFF indicator lamp OFF
|
Off | ||
| RELEASE SW NO | Ignition switch ON | When brake pedal is depressed | On |
| When brake pedal is not depressed | Off | ||
| RELEASE SW NC | Ignition switch ON | When brake pedal is depressed | Off |
| When brake pedal is not depressed | On | ||
| STP LMP DRIVE | Drive the vehicle and activate the vehicle-to-vehicle distance control mode | When ICC brake hold relay is activated | On |
| When ICC brake hold relay is not activated | Off | ||
| D RANGE SW | READY state | When the selector lever is in "D" position or manual mode | On |
| When the selector lever is in any position other than "D" or manual mode | Off | ||
| NP RANGE SW | READY state | When the selector lever is in "N", "P" position | On |
| When the selector lever is in any position other than "N", "P" | Off | ||
| PKB SW | Ignition switch ON | When the parking brake is applied | On |
| When the parking brake is released | Off | ||
| PWR SUP MONI | READY state | Power supply voltage value of ADAS control unit | |
| VHCL SPD AT | While driving | Value of A/T vehicle speed sensor signal | |
| THRTL OPENING | READY state | Depress accelerator pedal | Displays the throttle position |
| GEAR | While driving | Displays the gear position | |
| CLUTCH SW SIG |
NOTE:
The item is indicated, but not monitored |
0.0 | |
| NP SW SIG | Ignition switch ON | When the shift lever is in neutral position | On |
| When the shift lever is in any position other than neutral | Off | ||
| MODE SIG | Set the vehicle to READY and press MAIN switch | When ICC system is deactivated | Off |
| When vehicle-to-vehicle distance control mode is activated | ICC | ||
| SET DISP IND |
NOTE:
The item is indicated, but not monitored |
Off | |
| DISTANCE | Drive the vehicle and activate the vehicle-to-vehicle distance control mode | When a vehicle ahead is detected | Displays the distance from the preceding vehicle |
| When a vehicle ahead is not detected | 0.0 | ||
| ON ROOT GUIDANCE |
NOTE:
The item is indicated, but not monitored |
Off | |
| RELATIVE SPD | Drive the vehicle and activate the vehicle-to-vehicle distance control mode | When a vehicle ahead is detected | Displays the relative speed. |
| When a vehicle ahead is not detected | 0.0 | ||
| DYNA ASIST SW | Ignition switch ON | When dynamic driver assistance switch is pressed | On |
| When dynamic driver assistance switch is not pressed | Off | ||
| DCA ON IND | Set the vehicle to READY and press dynamic driver assistance switch (When DCA setting is ON) |
DCA system OFF | Off |
| DCA system ON | On | ||
| DCA VHL AHED | Drive the vehicle and activate the DCA system | When a vehicle ahead is not detected (vehicle ahead detection indicator OFF) | Off |
| When a vehicle ahead is detected (vehicle ahead detection indicator ON) | On | ||
| IBA SW |
NOTE:
The item is indicated, but not monitored |
Off | |
| APA TEMP | READY state | Display the accelerator pedal actuator integrated motor temperature | |
| APA PWR | Ignition switch ON | Power supply voltage value of accelerator pedal actuator | |
| LDW SYSTEM ON | Ignition switch ON | When the LDW system is ON | On |
| When the LDW system is OFF | Off | ||
| LDW ON LAMP | Ignition switch ON | Warning systems ON indicator ON | On |
| Warning systems ON indicator OFF | Off | ||
| LDP ON IND | Set the vehicle to READY and press dynamic driver assistance switch (When LDP system setting is ON) |
LDP ON indicator lamp ON | On |
| LDP ON indicator lamp OFF | Off | ||
| LANE DPRT W/L | Drive the vehicle and activate the LDW system or LDP system | Lane departure warning lamp ON | On |
| Lane departure warning lamp OFF | Off | ||
| LDW BUZER OUTPUT | Drive the vehicle and activate the LDW/LDP system or Blind Spot Warning/Blind Spot Intervention system | When the buzzer of the following system operates
|
On |
When the buzzer of the following system does not operate
|
Off | ||
| LDP SYSTEM ON | Set the vehicle to READY and press dynamic driver assistance switch (When LDP system setting is ON) |
When the LDP system is ON | On |
| When the LDP system is OFF | Off | ||
| READY signal | Set the vehicle to READY and press dynamic driver assistance switch (When LDP system setting is ON) |
When the LDP system is ON | On |
| When the LDP system is OFF | Off | ||
| Camera lost | Drive the vehicle and activate the LDW system, LDP system or Blind Spot Intervention system | Both side lane markers are detected | Detect |
| Deviate side lane marker is lost | Deviate | ||
| Both side lane markers are lost | Both | ||
| Lane unclear | While driving | Lane marker is unclear | On |
| Lane marker is clear | Off | ||
| STATUS signal | Drive the vehicle and activate the LDP system | When the LDP system is ON | Stnby |
| When the LDP system is operating | Warn | ||
| When the LDP system is canceled | Cancel | ||
| When the LDP system is OFF | Off | ||
| Shift position |
|
Displays the shift position | |
| Turn signal | Turn signal lamps OFF | Off | |
| Turn signal lamp LH blinking | LH | ||
| Turn signal lamp RH blinking | RH | ||
| Turn signal lamp LH and RH blinking | LH & RH | ||
| SIDE G | While driving | Vehicle turning right | Negative value |
| Vehicle turning left | Positive value | ||
| WARN REQ | Drive the vehicle and activate the LDP system | Lane departure warning is operating | On |
| Lane departure warning is not operating | Off | ||
| FUNC ITEM (FCW) | READY state | On | |
| FUNC ITEM (LDW) | READY state | On | |
| FUNC ITEM (BSW) | READY state | On | |
| FUNC ITEM (NV-ICC) |
NOTE:
The item is indicated, but not monitored |
Off | |
| FUNC ITEM (NV-DCA) |
NOTE:
The item is indicated, but not monitored |
Off | |
| DCA SELECT | Ignition switch ON | "Distance Control Assist" set with the integral switch is ON | On |
| "Distance Control Assist" set with the integral switch is OFF | Off | ||
| LDP SELECT | Ignition switch ON | "Lane Departure Intervention" set with the integral switch is ON | On |
| "Lane Departure Intervention" set with the integral switch is OFF | Off | ||
| BSI SELECT | Ignition switch ON | "Blind Spot Intervention" set with the integral switch is ON | On |
| "Blind Spot Intervention" set with the integral switch is OFF | Off | ||
| FCW SELECT | Ignition switch ON | "Forward Collision Warning" set with the integer switch is ON | On |
| "Forward Collision Warning" set with the integral switch is OFF | Off | ||
| LDW SELECT | Ignition switch ON | "Lane Departure Warning" set with the integral switch is ON | On |
| "Lane Departure Warning" set with the integral switch is OFF | Off | ||
| BSW SELECT | Ignition switch ON | "Blind Spot Warning" set with the integral switch is ON | On |
| "Blind Spot Warning" set with the integral switch is OFF | Off | ||
| NAVI ICC SELECT |
NOTE:
The item is indicated, but not monitored |
Off | |
| NAVI DCA SELECT |
NOTE:
The item is indicated, but not monitored |
Off | |
| SYS SELECTABILITY | Ignition switch ON | Items set with the integral switch can be switched normally | On |
| Items set with the integral switch cannot be switched normally | Off | ||
| DRIVE MODE STATS | Ignition switch ON | When drive mode select switch position is STANDARD | STD |
| When drive mode select switch position is in SPORT | SPORT | ||
| When drive mode select switch position is in ECO | ECO | ||
| When drive mode select switch position is in SNOW | SNOW | ||
| When drive mode select switch position is in PERSONAL | STD | ||
| A signal other than those above is input | ERROR | ||
| BSW/BSI WARN LMP | READY state | When the BSW system is malfunctioning | On |
| When the BSW system is normal | Off | ||
| BSI ON IND | READY state | Blind Spot Intervention warning ON | On |
| Blind Spot Intervention warning OFF | Off | ||
| BSW SYSTEM ON | Ignition switch ON | When the BSW system is ON | On |
| When the BSW system is OFF | Off | ||
| BSI SYSTEM ON | Set the vehicle to READY and press dynamic driver assistance switch (When Blind Spot Intervention system setting is ON) |
When the Blind Spot Intervention system is ON | On |
| When the Blind Spot Intervention system is OFF | Off | ||
| FCW SYSTEM ON | READY state | When the PFCW system is ON | On |
| When the PFCW system is OFF | Off | ||
| WARN SYS SW |
NOTE:
The item is indicated, but not monitored |
Off | |
| SYSTEM CANCEL MESSAGE | READY state | When the vehicle is normal | NOREQ |
| When the wheel is slipping | SLIP | ||
| When the drive mode selector is SNOW mode | SNOW | ||
| When the VDC is OFF | VDC OFF | ||
| ITS SETTING ITEM (DCA) | Ignition switch ON | On | |
| ITS SETTING ITEM (LDP) | Ignition switch ON | On | |
| ITS SETTING ITEM (BSI) | Ignition switch ON | On | |
| BATTERY CIRCUIT OFF |
NOTE:
The item is indicated, but not monitored |
Off | |
| LDP WARNING INDICATOR | READY state | When the LDP system is malfunctioning | On |
| When the LDP system is normal | Off | ||
| LDW ON INDICATOR | READY state | LDW system display ON | On |
| LDW system display OFF | Off | ||
| LDW WARNING INDICATOR | READY state | When the LDW system is malfunctioning | On |
| When the LDW system is normal | Off | ||
| CAMERA HI TEMP MSG | READY state | Lane camera unit high temperature warning display ON | On |
| Lane camera unit high temperature warning display OFF | Off | ||
| LDW WARNING ALERT TIMING |
NOTE:
The item is indicated, but not monitored |
Nothing | |
| BSI WARNING INDICATOR | READY state | When the Blind Spot Intervention system is malfunctioning | On |
| When the Blind Spot Intervention system is normal | Off | ||
| BSW ON INDICATOR | READY state | BSW system display ON | On |
| BSW system display OFF | Off | ||
| SIDE RADAR BLOCK COND | READY state | Front bumper or side radar is dirty | On |
| Front bumper and side radar is clean | Off | ||
| BSW IND BRIGHTNESS | Ignition switch ON | BSW system OFF | Nothing |
| Blind Spot Warning/Blind Spot Intervention indicator brightness bright | Bright | ||
| Blind Spot Warning/Blind Spot Intervention indicator brightness normal | Normal | ||
| Blind Spot Warning/Blind Spot Intervention indicator brightness dark | Dark | ||
| BCI SYSTEM ON | READY state | When the BCI system is ON | On |
| When the BCI system is OFF | Off | ||
| BCI SWITCH |
NOTE:
The item is indicated, but not monitored |
Off | |
| FUNC ITEM (FEB) | READY state | "Forward Emergency Braking" set with the integral switch is ON | On |
| "Forward Emergency Braking" set with the integral switch is OFF | Off | ||
| FEB SELECT | Ignition switch ON | "Forward Emergency Braking" set with the integral switch is ON | On |
| "Forward Emergency Braking" set with the integral switch is OFF | Off | ||
| FEB SW | READY state | FEB system ON | On |
| FEB system OFF | Off | ||