Active Test Mode
CAUTION:
- Do not perform active test while driving vehicle.
- Make sure to completely bleed air from brake system.
- The active test cannot be performed with the ABS warning lamp, VDC warning lamp and brake warning lamp are ON.
- ABS warning lamp, VDC warning lamp and brake warning lamp are ON during active test.
- Erase memory of "ICC/ADAS" with CONSULT-III, after implementing active test.
NOTE:
- When active test is performed while depressing the pedal, the pedal depression amount will change. This is normal. (Only solenoid valve and ABS motor.)
- "TEST IS STOPPED" in is displayed 10 seconds after operation start.
- After "TEST IS STOPPED" in "ABS" with CONSULT-III is displayed, to perform test again.
Test Item
ABS SOLENOID VALVE
- Select "Up", "Keep" and "Down" of "ACTIVE TEST" in "ABS" with CONSULT-III. Then use screen monitor to check that solenoid valve operates as shown in the table below.ACTIVE TEST CHART
Test item Display item (Note) Display Up Keep Down FR RH SOL FR RH IN SOL Off On On FR RH OUT SOL Off Off On(1) USV[FR-RL] Off Off Off HSV[FR-RL] Off Off Off FR LH SOL FR LH IN SOL Off On On FR LH OUT SOL Off Off On(1) USV[FL-RR] Off Off Off HSV[FL-RR] Off Off Off RR RH SOL RR RH IN SOL Off On On RR RH OUT SOL Off Off On(1) USV[FL-RR] Off Off Off HSV[FL-RR] Off Off Off RR LH SOL RR LH IN SOL Off On On RR LH OUT SOL Off Off On(1) USV[FR-RL] Off Off Off HSV[FR-RL] Off Off Off (1) On for 1 to 2 seconds after the select, and then Off. NOTE: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an operation for checking.
ABS SOLENOID VALVE (ACT)
- Select "Up", "ACT UP" and "ACT KEEP" of "ACTIVE TEST" in "ABS" with CONSULT-III. Then use screen monitor to check that solenoid valve operates as shown in the table below.ACTIVE TEST CHART
Test item Display item (Note) Display Up ACT UP ACT KEEP FR RH ABS SOLENOID (ACT) FR RH IN SOL Off Off Off FR RH OUT SOL Off Off Off USV[FR-RL] Off On On HSV[FR-RL] Off On(1) Off FR LH ABS SOLENOID (ACT) FR LH IN SOL Off Off Off FR LH OUT SOL Off Off Off USV[FL-RR] Off On On HSV[FL-RR] Off On(1) Off RR RH ABS SOLENOID (ACT) RR RH IN SOL Off Off Off RR RH OUT SOL Off Off Off USV[FL-RR] Off On On HSV[FL-RR] Off On(1) Off RR LH ABS SOLENOID (ACT) RR LH IN SOL Off Off Off RR LH OUT SOL Off Off Off USV[FR-RL] Off On On HSV[FR-RL] Off On(1) Off (1) On for 1 to 2 seconds after the select, and then Off. NOTE: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an operation for checking.
ABS MOTOR
- Select "On" and "Off" in of "ACTIVE TEST" in "ABS" with CONSULT-III. Make sure motor relay and actuator relay operates as shown in table below.ACTIVE TEST CHART
Test item Display item Display On Off ABS MOTOR MOTOR RELAY On Off ACTUATOR RLY (Note) On On NOTE: A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an operation for checking.