LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2011 >> EX35 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Engine Mechanical) >> Preparation >> Preparation >> Commercial Service Tools

Commercial Service Tools

WARNING: This page is about a different car, the 2008 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.
COMMERCIAL SERVICE TOOLS REFERENCE

(Kent-Moore No.)
Tool name		 Description
( - )
Tube presser
G04878211Courtesy of NISSAN MOTOR CO., U.S.A.
 Pressing the tube of liquid gasket
( - )
Power tool
G04874612Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening bolts and nuts
( - )
Manual lift table caddy
G04878219Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing engine
(J24239-01)
Cylinder head bolt wrench
G05207161Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening and tightening cylinder head bolt, and used with the angle wrench [SST:
KV10112100 (BT8653-A)]
  1. 13 mm (0.51 in) dia. 
  2. 12 mm (0.47 in) 
  3. 10 mm (0.39 in) 
( - )
  1. Compression gauge
  2. Adapter
G04878221Courtesy of NISSAN MOTOR CO., U.S.A.
 Checking compression pressure
( - )
Spark plug wrench
G05207163Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing spark plug
  1. 14 mm (0.55 in) 
( - )
Valve seat cutter set
G04878223Courtesy of NISSAN MOTOR CO., U.S.A.
 Finishing valve seat dimensions
( - )
Piston ring expander
G04878224Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing piston ring
( - )
Valve guide drift
G05207166Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing valve guide
Intake and Exhaust: 
  1. 9.5 mm (0.374 in) dia. 
  2. 5.5 mm (0.217 in) dia. 
( - )
Valve guide reamer
G05207167Courtesy of NISSAN MOTOR CO., U.S.A.
  1. Reaming valve guide inner hole
  2. Reaming hole for oversize valve guide

Intake and Exhaust: 
c: 6.0 mm (0.236 in) dia. 
d: 10.2 mm (0.402 in) dia. 
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner
G05207168Courtesy of NISSAN MOTOR CO., U.S.A.
 Reconditioning the exhaust system threads before installing a new air fuel ratio sensor and heated oxygen sensor (Use with anti-seize lubricant shown below.)
  1. J-43897-18 [18 mm (0.71 in) dia.] for zirconia heated oxygen sensor and air fuel ratio sensor 
  2. J-43897-12 [12 mm (0.47 in) dia.] for titania heated oxygen sensor 
  3. Mating surface shave cylinder
  4. Flutes
( - )
Anti-seize lubricant (Permatex 133AR or equivalent meeting MIL specification MIL-A-907)
G04878228Courtesy of NISSAN MOTOR CO., U.S.A.
 Lubricating oxygen sensor thread cleaning tool when reconditioning exhaust system threads
scientia non olet · About LEMON Manuals