LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2011 >> EX35 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 14 (Automatic Transmission) >> On-Vehicle Repair >> Control Valve And TCM >> Removal and Installation >> Removal

Removal and Installation: Removal

WARNING: This page is about a different car, the 2008 Infiniti EX35. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the battery cable from the negative terminal.
  2. Drain ATF through drain plug.
  3. Remove exhaust mounting bracket. Refer to "EXPLODED VIEW ".
  4. Disconnect heated oxygen sensor 2 harness connectors (A).
    Fig 1: Identifying Heated Oxygen Sensor 2 Harness And Clips
    G05726793Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Remove heated oxygen sensor 2 harness (B) from clips (1).
  6. Remove bracket (2) from transmission assembly.
  7. Disconnect A/T assembly harness connector.
  8. Remove snap ring (1) from A/T assembly harness connector (A).
    Fig 2: Removing Snap Ring From A/T Assembly Harness Connector
    G05218604Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Push A/T assembly harness connector (A).
    CAUTION: Be careful not to damage connector.
    Fig 3: Pushing A/T Assembly Harness Connector
    G05218605Courtesy of NISSAN MOTOR CO., U.S.A.
  10. Remove clips (1).
  11. Remove oil pan (2) and oil pan gasket.
    Fig 4: Locating Oil Pan Bolts
    G05726796Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Remove magnets (1) from oil pan.
    Fig 5: Identifying Oil Pan Magnets
    G05218607Courtesy of NISSAN MOTOR CO., U.S.A.
  13. Disconnect A/T fluid temperature sensor 2 connector (A).
    CAUTION: Be careful not to damage connector.
  14. Disengage terminal clips (<=).
    Fig 6: Locating A/T Fluid Temperature Sensor Connector
    G04875912Courtesy of NISSAN MOTOR CO., U.S.A.
  15. Disconnect revolution sensor connector (A).
    CAUTION: Be careful not to damage connector.
  16. Disengage terminal clip (<=).
    Fig 7: Locating Revolution Sensor Connector
    G05218609Courtesy of NISSAN MOTOR CO., U.S.A.
  17. Remove bolts (A), (B) and (C) from control valve with TCM.
    Fig 8: Identifying Bolts And Control Valve With TCM
    G05726800Courtesy of NISSAN MOTOR CO., U.S.A.
  18. Remove control valve with TCM from transmission case.
    CAUTION: When removing, be careful with the manual valve (1) notch and manual plate (2) height. Remove it vertically.
    Fig 9: Removing Control Valve With TCM From Transmission Case
    G05218611Courtesy of NISSAN MOTOR CO., U.S.A.
  19. Remove A/T fluid temperature sensor 2 (1) with bracket (2) from control valve with TCM.
    Fig 10: Identifying A/T Fluid Temperature Sensor 2 And Bracket
    G05726802Courtesy of NISSAN MOTOR CO., U.S.A.
  20. Remove bracket (1) from A/T fluid temperature sensor 2 (2).
    Fig 11: Identifying Bracket And A/T Fluid Temperature Sensor 2
    G05218613Courtesy of NISSAN MOTOR CO., U.S.A.
  21. Remove O-ring (1) from A/T assembly harness connector (A).
    Fig 12: Identifying O-Ring
    G05218614Courtesy of NISSAN MOTOR CO., U.S.A.
  22. Disconnect TCM connectors (A) and (B).
    CAUTION: Be careful not to damage connectors.
    Fig 13: Identifying TCM Connectors
    G05218615Courtesy of NISSAN MOTOR CO., U.S.A.
  23. Remove A/T assembly harness connector (A) from control valve with TCM using flat-blade screwdriver (B).
    Fig 14: Removing A/T Assembly Harness Connector From Control Valve
    G05218616Courtesy of NISSAN MOTOR CO., U.S.A.
  24. Disconnect TCM connector (A) and park/neutral position switch connector (B).
    CAUTION: Be careful not to damage connectors.
    Fig 15: Identifying TCM Connector And Park/Neutral Position Switch Connector
    G05218617Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals