LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2008 >> M35 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 57 (Sliding Roof) >> Sliding Roof System >> Data List / Active Test

Data List / Active Test

WARNING: This page is about a different car, the 2008 Toyota Tundra. However, it is still accessible from the selected car via links, so may be relevant.
  1. DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the tester on.
    4. Enter the following menus:

      Select: Body Electrical / Sliding Roof / Data List.

    5. According to the display on tester, read the "Data List".

      Sliding Roof 

      SLIDING ROOF - DATA LIST

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open Switch Slide switch open signal/ON or OFF ON: SLIDE switch is pressed to open
      OFF: SLIDE switch is not pressed to open      		 -
      Close Switch Slide switch close signal/ON or OFF ON: SLIDE switch is pressed to close
      OFF: SLIDE switch is not pressed to close      		 -
      Up Switch Tilt switch up signal/ON or OFF ON: TILT switch is pressed to up
      OFF: TILT switch is not pressed to up      		 -
      Down Switch Tilt switch down signal/ON or OFF ON: TILT switch is pressed to down
      OFF: TILT switch is not pressed to down      		 -
      Hall IC1 Status Sliding roof operation signal/ NORMAL or LOCK NORMAL: Sliding roof motor is operating
      LOCK: Sliding roof motor is not operating      		 -
      Hall IC1 Pulse Sliding roof operation signal/LO or HI LO: Sliding roof motor is not operating
      HI: Sliding roof motor is operating      		 -
      Hall IC2 Status Sliding roof operation signal/ NORMAL or LOCK NORMAL: Sliding roof motor is operating
      LOCK: Sliding roof motor is not operating      		 -
      Hall IC2 Pulse Sliding roof operation signal/LO or HI LO: Sliding roof motor is not operating
      HI: Sliding roof motor is operating      		 -
      Ignition (Direct Signal) Ignition switch signal/ON or OFF ON: Ignition switch ON
      OFF: Ignition switch OFF      		 -
      Ignition (MPX) Ignition switch signal (MPX signal)/ON or OFF ON: Ignition switch ON
      OFF: Ignition switch OFF      		 -
      Door Courtesy Driver's door courtesy light switch signal/ON or OFF ON: Driver's door is open
      OFF: Driver's door is closed      		 -
      Door Key Close Operation Key-linked sliding roof open signal/ON or OFF ON: Door key cylinder is turned to UNLOCK position using key
      OFF: Door key cylinder is not turned to UNLOCK      		 -
      Door Key Open Operation Key-linked sliding roof close signal/ON or OFF ON: Door key cylinder is turned to LOCK position using key
      OFF: Door key cylinder is not turned to LOCK      		 -
      Key Off Permission Key-off sliding roof operation permit signal/ON or OFF ON: Driver's side door is not closed within 45 sec after ignition switch is turned OFF
      OFF: Any status except "ON" status      		 -
      Door Key Related (Open) Key-linked sliding roof open operation status/Avail or Not Avail Avail: Key-linked sliding roof open operation is available
      Not Avail: Key-linked sliding roof open operation is not available      		 -
      Door Key Related (Close) Key-linked sliding roof close operation status/Avail or Not Avail Avail: Key-linked sliding roof close operation is available
      Not Avail: Key-linked sliding roof close operation is not available      		 -
      Door Key Related Operation Direction for key-linked operation/ Tilt or Slide Tilt: Key-linked sliding roof operation operates tilt up or down
      Slide: Key-linked sliding roof operation operates slide open or close      		 -
      Down Switch Failure (Current) Down switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt down signal failure (Current)
      Not Fail: Sliding roof tilt down signal not fail (Current)      		 -
      Up Switch Failure (Current) Up switch failure signal (Current)/ Fail or Not Fail Fail: Sliding roof tilt up signal failure (Current)
      Not Fail: Sliding roof tilt up signal not fail (Current)      		 -
      Close Switch Failure (Current) Close switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof close signal failure (Current)
      Not Fail: Sliding roof close signal not fail (Current)      		 -
      Open Switch Failure (Current) Open switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof open signal failure (Current)
      Not Fail: Sliding roof open signal not fail (Current)      		 -
      Down Switch Failure (Past) Down switch failure signal (Past)/ Fail or Not Fail Fail: Sliding roof tilt down signal failure (Past)
      Not Fail: Sliding roof tilt down signal not fail (Past)      		 -
      Up Switch Failure (Past) Up switch failure signal (Past)/ Fail or Not Fail Fail: Sliding roof tilt up signal failure (Past)
      Not Fail: Sliding roof tilt up signal not fail (Past)      		 -
      Close Switch Failure (Past) Close switch failure signal (Past)/ Fail or Not Fail Fail: Sliding roof close signal failure (Past)
      Not Fail: Sliding roof close signal not fail (Past)      		 -
      Open Switch Failure (Past) Open switch failure signal (Past)/ Fail or Not Fail Fail: Sliding roof open signal failure (Past)
      Not Fail: Sliding roof open signal not fail (Past)      		 -
  2. ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the tester on.
    4. Enter the following menus:

      Select: Body Electrical / Sliding Roof / Active Test.

    5. According to the display on tester, perform the "Active Test".

      Sliding Roof 

      SLIDING ROOF - ACTIVE TEST LIST

      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof SLIDE CLOSE/TILT UP or SLIDE OPEN/TILT DOWN CLOS/UP: Sliding roof SLIDE
      CLOSE or TILT UP operation occurs
      OPN/DWN: Sliding roof SLIDE
      OPEN or TILT DOWN operation occurs
      OFF: Sliding roof is not operating      		 -
scientia non olet · About LEMON Manuals