LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2006 >> M35 Base >> Repair and Diagnosis >> Body & Frame >> Seats >> Automatic Drive Positioner >> Tilt Switch Circuit Check

Tilt Switch Circuit Check

  1. CHECK FUNCTION 

    With CONSULT-II 

    With "TILT SW-UP, TILT SW-DOWN" on the DATA MONITOR, operate the ADP steering switch to check ON/OFF operation.

    MONITOR ITEM CONTENTS

    Monitor item [OPERATION or UNIT] Contents
    TILT SW-UP "ON/OFF" (ON/OFF) status judged from the tilt switch (UP) signal is displayed.
    TILT SW-DOWN "ON/OFF" (ON/OFF) status judged from the tilt switch (DOWN) signal is displayed.
    Fig 1: CONSULT II DATA MONITOR Screen
    G04146007Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Check voltage between automatic drive positioner control unit connector and ground.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND VOLTAGE

      Automatic drive positioner control unit connector Terminals Tilt switch condition Voltage (V) (Approx.)
      (+) (-)
      M6 1 Ground UP 0
      Other than above 5
      17 DOWN 0
      Other than above 5
      Fig 2: Identifying Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
      G04146008Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Tilt switch circuit is OK.

    NG: GO TO 2.

  2. CHECK TILT SWITCH CIRCUIT HARNESS CONTINUITY 
    1. Disconnect automatic drive positioner control unit connector and ADP steering switch connector.
    2. Check continuity between automatic drive positioner control unit connector and ADP steering switch connector.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND ADP STEERING SWITCH CONNECTOR CONTINUITY

      A B Continuity
      Automatic drive positioner control unit connector Terminal ADP steering switch connector Terminal
      M6 1 M46 2 Yes
      17 3
    3. Check continuity between automatic drive positioner control unit connector and ground.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND CONTINUITY

      A Ground Continuity
      Automatic drive positioner control unit connector Terminal
      M6 1 No
      17
      Fig 3: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector And ADP Steering Switch Connector
      G04146009Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 3.

    NG: Repair or replace harness.

  3. CHECK ADP TILT STEERING SWITCH 

    ADP steering switch operate, check continuity ADP steering switch.

    ADP STEERING SWITCH CONTINUITY

    ADP steering switch Terminal ADP steering switch condition Continuity
    M46 2 1 UP Yes
    Other than above No
    3 DOWN Yes
    Other than above No
    Fig 4: Identifying ADP STEERING SWITCH CONTINUITY
    G04146010Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 6.

    NG: Replace ADP steering switch.

  4. CHECK ADP STEERING SWITCH GROUND CIRCUIT 

    Check continuity between ADP steering switch connector and ground.

    ADP STEERING SWITCH CONNECTOR AND GROUND CONTINUITY

    ADP steering switch connector Terminal Ground Continuity
    M46 1 Yes
    Fig 5: Identifying Continuity Between ADP Steering Switch Connector And Ground
    G04146011Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace automatic drive positioner control unit.

    NG: Repair or replace harness.

scientia non olet · About LEMON Manuals