LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2006 >> FX45 >> Repair and Diagnosis >> Body & Frame >> Seats >> Automatic Drive Positioner >> Check Telescopic Switch Circuit

Check Telescopic Switch Circuit

  1. CHECK FUNCTION 

    With CONSULT-II 

    With "TELESCO SW-FR, TELESCO SW-RR" on the DATA MONITOR, operate the ADP steering switch to check ON/OFF operation.

    MONITOR ITEM CHART

    Monitor item [OPERATION or UNIT] Contents
    TELESCO SW-FR "ON/OFF" (ON/OFF) status judged from the telescoping switch (FR) signal is displayed.
    TELESCO SW-RR "ON/OFF" (ON/OFF) status judged from the telescoping switch (RR) signal is displayed.
    Fig 1: CONSULT-II Function Display - DATA MONITOR
    G04077712Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Telescopic switch operate, check voltage between automatic drive positioner control unit connector and ground.
      TERMINAL VOLTAGE CHART

      Connector Terminals (Wire color) Telescopic switch condition Voltage (V) (Approx.)
      (+) (-)
      M49 11 (BR) Ground FORWARD 0
      Other than above 5
      27 (LG) BACKWARD 0
      Other than above 5
      Fig 2: Identifying Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
      G04077713Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK : Telescopic switch circuit is OK.

    NG : GO TO 2.

  2. CHECK TELESCOPIC CIRCUIT HARNESS CONTINUITY 
    1. Disconnect automatic drive positioner control unit connector and ADP steering switch connector.
    2. Check continuity between automatic drive positioner control unit connector M49 terminals 11, 27 and ADP steering switch connector M13 terminals 4, 5.

      11 (BR) - 5 (BR) : Continuity should exist. 

      27 (LG) - 4 (LG) : Continuity should exist. 

    3. Check continuity between automatic drive positioner control unit connector M49 terminals 11, 27 and ground.

      11 (BR) - Ground : Continuity should not exist. 

      27 (LG) - Ground : Continuity should not exist. 

      Fig 3: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector M49 Terminals 11, 27 And Ground
      G04077714Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK : GO TO 3.

    NG : Repair or replace harness between automatic drive positioner control unit and ADP steering switch.

  3. CHECK TELESCOPIC SWITCH 

    ADP steering switch operate, check continuity between ADP steering switch connector M13 terminal 4, 5 and 1.

    TERMINAL CONTINUITY CHART

    Connector Terminal ADP steering switch condition Continuity
    M13 5 1 FORWARD Yes
    Other than above No
    4 BACKWARD Yes
    Other than above No

    OK or NG 

    OK : GO TO 4.

    NG : Replace ADP steering switch.

    Fig 4: Identifying Continuity Between ADP Steering Switch Connector M13 Terminal 4, 5 And 1
    G04077715Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK ADP STEERING SWITCH GROUND CIRCUIT 

    Check continuity between ADP steering switch connector M13 terminal 1 and ground.

    1 (B) - Ground : Continuity should exist. 

    OK or NG 

    OK : Check the condition of the harness and connector.

    NG : Replace or replace harness between ADP steering switch and ground.

    Fig 5: Identifying Continuity Between ADP Steering Switch Connector M13 Terminal 1 And Ground
    G04077716Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals