Check Passenger Side Mirror Sensor Circuit

CHECK DOOR MIRROR FUNCTION
Check the following.

Operation malfunction in memory control

NOTE: If a door mirror face position is set to an implausible angle, the set position may not be reproduced.

OK or NG

OK : GO TO 2.

NG : Repair the malfunctioning parts, and check the symptom again.

CHECK MIRROR SENSOR INSPECTION

With CONSULT-II

Make sure "ON" is displayed on "MIR/SE RH R-L, MIR/SE RH U-D" in the DATA MONITOR.

MONITOR ITEM CHART

Monitor item [OPERATION or UNIT]		Contents
MIR/SE RH R-L	"V"	Voltage output from RH door mirror sensor (LH/RH) is displayed.
MIR/SE RH U-D	"V"	Voltage output from RH door mirror sensor (UP/DOWN) is displayed.

Fig 1: CONSULT-II Function Display - DATA MONITOR

Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II

Turn ignition switch to ACC position.

Check voltage between door mirror (passenger side) connector and ground.

TERMINAL VOLTAGE CHART

Connector	Terminals (Wire color)		Condition	Voltage (V) (Approx.)
Connector	(+)	(-)	Condition	Voltage (V) (Approx.)
D32	2 (LG)	Ground	When motor is UP or DOWN operation	Changes between 3 (close to perk) - 1 (close to valley)
D32	10 (P)	Ground	When motor is LEFT or RIGHT operation	Changes between 1 (close to left edge) - 3 (close to right edge)

Fig 2: Identifying Voltage Between Door Mirror (Passenger Side) Connector And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK : Passenger side mirror sensor circuit is OK.

NG : GO TO 3.

CHECK HARNESS CONTINUITY 1
1. Disconnect automatic drive positioner control unit and door mirror (passenger side) connector.
2. Check continuity between automatic drive positioner control unit connector M50 terminal 33, 41 and door mirror (passenger side) connector D32 terminal 1, 9.
  33 (G/W) - 1 (BR) : Continuity should exist.
  
  41 (B/Y) - 9 (G) : Continuity should exist.
3. Check continuity between automatic drive positioner control unit connector M50 terminals 33, 41 and ground.
  33 (G/W) - Ground : Continuity should not exist.
  
  41 (B/Y) - Ground : Continuity should not exist.
  
  Fig 3: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector M50 Terminals 33, 41 And Ground
  Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NG

OK : GO TO 3.

NG : Repair or replace harness between automatic drive positioner control unit and door mirror (passenger side).
CHECK HARNESS CONTINUITY 2
1. Check continuity between automatic drive positioner control unit connector M49 terminal 5, 21 and door mirror (passenger side) connector D32 terminal 2, 10.
  5 (OR) - 2 (LG) : Continuity should exist.
  
  21 (G/Y) - 10 (P) : Continuity should exist.
2. Check continuity between automatic drive positioner control unit connector M49 terminal 5, 21 and ground.
  5 (OR) - Ground : Continuity should not exist.
  
  21 (G/Y) - Ground : Continuity should not exist.
  
  Fig 4: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector M49 Terminal 5, 21 And Ground
  Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NG

OK : Check the condition of the harness and connector.

NG : Repair or replace harness between automatic drive positioner control unit and door mirror (passenger side).