Limit Switch Circuit Check (Passenger Side)

1. Turn ignition switch ON.
2. Check voltage between front power window regulator (passenger side) connector and ground.
   Fig 1: Checking Front Power Window Switch (Passenger Side) Limit Signal

   Courtesy of NISSAN MOTOR CO., U.S.A.
   Fig 2: Checking Front Power Window Switch (Passenger Side) Ground Circuit

   Courtesy of NISSAN MOTOR CO., U.S.A.
   FRONT POWER WINDOW SWITCH (PASSENGER SIDE) VOLTAGE
   
   

   Connector	Terminals (Wire color)		Condition	Voltage (V) (Approx.)
   	(+)	(-)
   D38	5(GY)	Ground	Passenger side door window is between fully-open and just before fully-closed position (ON)	0
   			Passenger side door window is between just before fully-closed position and fully-closed position (OFF)	5

OK or NG

1. OK: Limit switch circuit is OK.
2. NG: GO TO 2.

1. Turn ignition switch OFF.
2. Disconnect front power window regulator (passenger side) connector.
3. Check continuity between front power window regulator (passenger side) connector D38 terminal 6 and ground.

   6 (SB) - Ground: Continuity should exist. 

OK or NG

1. OK: GO TO  4 .
2. NG: GO TO 3.

1. Disconnect front power window switch (passenger side) connector.
2. Check continuity between front power window switch (passenger side) connector D36 terminal 3 and front power window regulator (passenger side) connector D38 terminal 6.
   Fig 3: Checking Front Power Window Switch (Passenger Side) Harness Continuity 1

   Courtesy of NISSAN MOTOR CO., U.S.A.

   3 (SB) - 6 (SB): Continuity should exist. 

OK or NG

1. OK: Replace front power window switch (passenger side).
2. NG: Repair or replace harness between front power window switch (passenger side) and front power window regulator (passenger side).

1. Turn ignition switch ON.
2. Check voltage between front power window switch (passenger side) connector D36 terminal 15 and ground.
   Fig 4: Checking Front Power Window Switch (Passenger Side) Output Signal

   Courtesy of NISSAN MOTOR CO., U.S.A.

   15 (GY) - Ground: Approx. 5V 

OK or NG

1. OK: GO TO 5
2. NG: Replace front power window switch (passenger side).

1. Turn ignition switch OFF.
2. Disconnect front power window switch (passenger side) connector.
3. Check continuity between front power window switch (passenger side) connector D36 terminal 15 and front power window regulator (passenger side) connector D38 terminal 5.
   Fig 5: Checking Front Power Window Switch (Passenger Side) Harness Continuity 2

   Courtesy of NISSAN MOTOR CO., U.S.A.

   15 (GY) - 5 (GY): Continuity should exist. 

OK or NG

1. OK: GO TO 6.
2. NG: Repair or replace harness between front power window switch (passenger side) and front power window regulator (passenger side).

1. Connect front power window regulator (passenger side) and front power window switch (passenger side) connector.
2. Turn ignition switch ON.
3. Check continuity between front power window regulator (passenger side) connector D38 terminal 5 and 6.
   Fig 6: Checking Limit Switch (Passenger Side)

   Courtesy of NISSAN MOTOR CO., U.S.A.
   LIMIT SWITCH (PASSENGER SIDE) CONTINUITY
   
   

   Connector	Terminals (Wire color)		Condition	Continuity
   D38	5(GY)	6 (SB)	Passenger side door window is between fully-open and just before fully-closed position (ON)	Yes (1)
   			Passenger side door window is between just before fully-closed position and fully-closed position (OFF)	No (1)
   (1) When checking continuity, turn ignition switch OFF.

OK or NG

1. OK: Check condition of harness and connector.
2. NG: Replace front power window motor (passenger side).