LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 1995 >> Q45 Base >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 4.5L V8 >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Camshaft Bearing Cap Bolt (1) 10 (14)
Camshaft Sprocket Bolt 12-16 (16-22)
Connecting Rod Nut
Step 1 10-12 (14-16)
Step 2 Additional 60-65 Degrees
Crankshaft Pulley Bolt 261-275 (353-373)
Crossmember Bolt/Nut 72-87 (98-118)
Cylinder Head Bolt (2)
Step 1 22 (30)
Step 2 69 (94)
Step 3 Loosen All Bolts
Step 4 18-25 (24-34)
Step 5 Additional 90-95 Degrees
EGR Tube 29-36 (39-49)
Engine Mount-To-Crossmember Nut 41-49 (56-66)
Engine Mount-To-Engine Bracket Nut 32-41 (43-56)
Exhaust Manifold Nut (3) 20-23 (27-31)
Flywheel Bolt 61-69 (83-94)
Fuel Injector Rail Bolt (4)
Step 1 (5)
Step 2 15-20 (20-27)
Lower Control Arm-To-Crossmember Bolt 94-108 (127-146)
Lower Intake Manifold Bolt 12-15 (16-20)
Main Bearing Cap Bolt/Nut (6)
Oil Pump Cover
Long Bolt 12-15 (16-20)
Short Bolt (7)
Oil Pump Sprocket Nut 22-30 (30-41)
Oxygen Sensor 30-37 (41-50)
Regulator Valve Plug 29-51 (39-69)
Spark Plug 15-21 (20-29)
Stabilizer Bar Link-To-Lower Control Arm Nut 14-22 (19-30)
Stabilizer Bar-To-Frame Bracket Nut 30-35 (41-47)
Starter 22-30 (30-41)
Tension Rod Bracket Bolt 72-87 (98-118)
Tension Rod-To-Lower Control Arm Nut 72-87 (98-118)
Thermostat Housing Bolt 12-15 (16-20)
Throttle Body Bolt
Step 1 (5)
Step 2 13-16 (18-22)
Timing Chain Guide Bolt 10-14 (14-19)
Torque Converter-To-Flywheel Bolt 33-43 (45-58)
Transmission Crossmember Bolt 32-41 (43-56)
Transmission Mount-To-Crossmember Bolt 16-21 (22-29)
Transmission Mount-To-Transmission Bolt 32-41 (43-56)
Upper Intake Manifold Bolt 11 (15)
Water Pump Bolt 12-15 (16-20)
INCH Lbs. (N.m) 
Front Cover Bolt (8)
Lower Front Cover Bolt 71 (8)
Upper Front Cover Bolt
Long Bolt 71 (8)
Short Bolt 97 (11)
Fuel Injector Clamp Bolt 27 (3)
Oil Pan Bolt/Nut (9) 71 (8)
Oil Pump Chain Guide Bolt 71 (8)
Oil Seal Retainer Bolt 71 (8)
Sub-Fuel Line Bolt (10)
Step 1 44 (5)
Step 2 89 (10)
Valve Cover Bolt (11)
Step 1 35 (4)
Step 2 87-104 (10-12)
(1) Tighten to specification in sequence. See Figure .
(2) Tighten to specification in sequence. See Figure .
(3) Tighten to specification in sequence. See Figure .
(4) Tighten to specification in sequence. See Figure .
(5) Tighten to 89 INCH lbs. (10 N.m).
(6) Tighten to specification in sequence. See Figure .
(7) Tighten to 44 INCH lbs. (5 N.m).
(8) Tighten to specification in sequence. See Figure .
(9) Tighten to specification in sequence. See Figure .
(10) Tighten to specification in sequence. See Figure .
(11) Tighten to specification in sequence. See Figure .