Repair Procedures: Removal

Remove the engine cover.
(Refer to "ENGINE COVER ")
Remove the air cleaner assembly and air duct.
(Refer to "AIR CLEANER ")
Remove the battery and battery tray.
(Refer to "BATTERY ")
Disconnect the inhibitor switch connect (A) and solenoid valve connector (B).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the CKP sensor (A).
Tightening torque:
1. 6.9 ~ 9.8 N.m (0.7 ~ 1.0 kgf.m, 5.1 ~ 7.2 lb-ft)
Courtesy of HYUNDAI MOTOR AMERICA
Remove the shift cable (B) after removing the nut (C) and the bolt (A).
Tightening torque:

(A) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

(C) 7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the ground line after removing the bolt (A).
Tightening torque:
1. 10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.1 ~ 10.1 lb-ft)
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring bracket installation bolt (A).

Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the coolant hose (B) after removing the automatic transaxle coolant hose clamp (A).

Remove the wiring mounting clip (C).

G12034180

Courtesy of HYUNDAI MOTOR AMERICA

G12034181

Courtesy of HYUNDAI MOTOR AMERICA

Remove the coolant pipe mounting bolts (A).

Remove the coolant pipe (B).

Tightening torque:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

G12034182

Courtesy of HYUNDAI MOTOR AMERICA

G12034183

Courtesy of HYUNDAI MOTOR AMERICA

Remove the wiring bracket installation bolt (A).

Courtesy of HYUNDAI MOTOR AMERICA
After loosening the mounting clips, then remove the fender side cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the pad (A).

Courtesy of HYUNDAI MOTOR AMERICA
Assembled the engine support fixture (A).
(Refer to SPECIAL SERVICE TOOLS .

Courtesy of HYUNDAI MOTOR AMERICA
Remove the hood.
(Refer to HOOD )
Using the engine support fixture (A), hold the engine and transaxle assembly safely.

Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle upper mounting bolts (A) and the starter motor mounting bolt (B).
Tightening torque:
1. 63.7 ~ 83.4 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)
2. 32.4 ~ 49.0 N.m (3.3 ~ 5.0 kgf.m, 23.9 ~ 36.2 lb-ft)
Courtesy of HYUNDAI MOTOR AMERICA
Remove the mounting bracket cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting bracket bolt (A).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting support bracket bolts (A).
Remove the automatic transaxle mounting support bracket (B).
Tightening torque:

58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the under cover (A).
Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the side cover (A).
Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the following items;
2WD
- Sub frame assembly.
  (Refer to "SUB FRAME ")
- Remove the drive shaft assembly.
  (Refer to FRONT DRIVESHAFT )
4WD
- Sub frame assembly.
  (Refer to "SUB FRAME ")
- Front muffler.
  (Refer to "MUFFLER ")
- Drive shaft assembly.
  (Refer to DRIVESHAFT ASSEMBLY )
- Transfer assembly.
  (Refer to TRANSFER ASSEMBLY )
Remove the dust cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the torque converter mounting bolts (A) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the start motor mounting bolt (A).
Tightening torque:

49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle with a jack after removing the mounting bolts (A, B).
Tightening torque:
1. 39.2 ~ 46.1 N.m (4.0 ~ 4.7 kgf.m, 28.9 ~ 34.0 lb-ft)
2. 78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)
Courtesy of HYUNDAI MOTOR AMERICA