LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2017 >> Santa Fe Sport Base, FWD >> Repair and Diagnosis >> Suspension >> Wheel Alignment >> Front Suspension System And Wheel Alignment >> Front Strut Assembly >> Repair Procedures >> Removal

Repair Procedures: Removal

  1. Remove the front wheel and tire (A) from front hub.

    Tightening torque: 

    88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

    CAUTION: Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
    Fig 1: Removing Front Wheel And Tire From Front Hub
    G12056008Courtesy of HYUNDAI MOTOR AMERICA
  2. Remove the brake hose (A) & wheel speed sensor (B) from the front strut assembly by loosening mounting bolts.

    Tightening torque: 

    6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

    Fig 2: Removing Brake Hose & Wheel Speed Sensor From Front Strut Assembly
    G12056009Courtesy of HYUNDAI MOTOR AMERICA
  3. Disconnect the stabilizer link (B) with the front strut assembly (A) after loosening the nut.

    Tightening torque: 

    98.1 ~ 117.7 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.8 lb-ft)

    Fig 3: Disconnecting Stabilizer Link With Front Strut Assembly
    G12056010Courtesy of HYUNDAI MOTOR AMERICA
  4. Disconnect the front strut assembly (A) with the knuckle by loosening the bolt & nut.

    Tightening torque: 

    137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

    Fig 4: Disconnecting Front Strut Assembly With Knuckle
    G12056011Courtesy of HYUNDAI MOTOR AMERICA
  5. Remove the fender apron upper cover (A).

    [LH] 

    Fig 5: Removing Fender Apron Upper Cover (LH)
    G12056012Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 6: Removing Fender Apron Upper Cover (RH)
    G12056013Courtesy of HYUNDAI MOTOR AMERICA
  6. Remove the mounting retainer (A) located at the end of the cowl top cover and the service cover (B).

    [LH] 

    Fig 7: Removing Mounting Retainer (LH)
    G12056014Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 8: Removing Mounting Retainer (RH)
    G12056015Courtesy of HYUNDAI MOTOR AMERICA
  7. Slightly pull the cowl top cover to your side to make a gap and loosen the strut mounting nuts (A-3 ea).

    Tightening torque: 

    53.9 ~ 73.5 N.m (5.5 ~ 7.5 kgf.m, 39.8 ~ 54.2 lb-ft)

  8. Remove the strut assembly (B).

    [LH] 

    Fig 9: Removing Strut Mounting Nuts (LH)
    G12056016Courtesy of HYUNDAI MOTOR AMERICA

    [RH] 

    Fig 10: Removing Strut Mounting Nuts (RH)
    G12056017Courtesy of HYUNDAI MOTOR AMERICA
  9. Install in the reverse order of removal.
  10. Check the front alignment.

    (Refer to Front Suspension System - "FRONT ALIGNMENT ")