Repair Procedures: Removal

Engine cover.
(Refer to "ENGINE COVER ")
Air cleaner assembly and air duct.
(Refer to "AIR CLEANER ")
Battery and battery tray.
(Refer to "BATTERY ")
Remove the ECM (Engine Control Module).
(Refer to "ENGINE CONTROL MODULE (ECM) ")
Remove the ground line after removing the bolt (A).

Fig 1: Removing Ground Line Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).

Fig 2: Disconnecting Solenoid Valve Connector And Inhibitor Switch Connector
Courtesy of HYUNDAI MOTOR AMERICA
Remove the control cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:
1. 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
2. 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Fig 3: Removing Control Cable Nut And Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Fig 4: Removing Automatic Transaxle Fluid Cooler Hose Clamp
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring mounting bolt (A).

Fig 5: Removing Wiring Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the solenoid valve connector and inhibitor switch connector wiring mounting bracket (A) and (B).
Tightening torque:

Bolt (A): 9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Bolt (B): 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

Fig 6: Removing Solenoid Valve Connector And Inhibitor Switch Connector Wiring Mounting Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Using the engine support fixture (beam No.: 09200-38001 or 09200-3N000, supporter No.:09200-2S100/2S200, adapter No.: 09200-4X000), hold the engine and transaxle assembly safely.

Fig 7: Holding Engine And Transaxle Assembly Safely
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).
Tightening torque:

(A, B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 8: Removing Automatic Transaxle Upper Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting bracket cover (A).

Fig 9: Removing Automatic Transaxle Mounting Bracket Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting bracket bolts (A).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)

Fig 10: Removing Automatic Transaxle Mounting Bracket Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting support bracket (A).
Tightening torque:

58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

Fig 11: Removing Automatic Transaxle Mounting Support Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Lift the vehicle with a jack.
Remove the under cover (A).
Tightening torque:

6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

Fig 12: Removing Under Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the roll rod bracket (A).
Tightening torque:

Nut (B): 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)

Bolts (C): 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

Fig 13: Removing Roll Rod Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Remove the air guide bracket (A).
Tightening torque:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

Fig 14: Removing Air Guide Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Remove the following items.
- Drive shaft assembly.
  (Refer to "FRONT DRIVESHAFT ")
Remove the dust cover (A).
Tightening torque:

42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Fig 15: Removing Dust Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the torque converter mounting bolt (A-4ea) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Fig 16: Removing Torque Converter Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
NOTE:
- Lubricant should be applied on thread of bolt before tightening.
Remove the heat protector (A).
Tightening torque:

19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

Fig 17: Removing Heat Protector
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle with a jack after removing the mounting bolt (A-1ea, B-3ea).
Tightening torque:
1. 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
2. 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
Fig 18: Removing Automatic Transaxle Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA