LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2016 >> Sonata Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 86 (Roof Trim) >> Roof Trim Assembly >> Repair Procedures >> Replacement

Repair Procedures: Replacement

WARNING: This page is about a different car, the 2016 Hyundai Elantra GT and 2015 Hyundai Elantra GT. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
  • Put on gloves to protect your hands.
NOTE:
  • Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
  1. Remove the front seat assembly.

    (Refer to "FRONT SEAT ASSEMBLY ")

  2. Remove the rear seat assembly.

    (Refer to "REAR SEAT ASSEMBLY ")

  3. Remove the front door scuff trim.

    (Refer to "DOOR SCUFF TRIM ")

  4. Remove the rear door scuff trim.

    (Refer to "DOOR SCUFF TRIM ")

  5. Remove the front pillar trim.

    (Refer to "FRONT PILLAR TRIM ")

  6. Remove the canter pillar lower trim.

    (Refer to "CENTER PILLAR TRIM ")

  7. Remove the canter pillar upper trim.

    (Refer to "CENTER PILLAR TRIM ")

  8. Remove the luggage side trim.

    (Refer to "LUGGAGE SIDE TRIM ")

  9. Remove the rear pillar trim.

    (Refer "REAR PILLAR TRIM ")

  10. Remove the sunvisor and retainer.

    (Refer to "SUNVISOR ")

  11. Remove the assist handle.

    (Refer to "ASSIST HANDLE ")

  12. Remove the overhead console lamp.

    (Refer to "OVERHEAD CONSOLE LAMP ")

  13. Remove the room lamp. [General type]

    (Refer to "ROOM LAMP ")

  14. Remove the ECM mirror cover (B).
  15. Disconnect the ECM mirror connector (A).
    Fig 1: Removing ECM Mirror Cover & Disconnecting Mirror Connector
    G10751075Courtesy of HYUNDAI MOTOR AMERICA
  16. Remove the auto defog sensor cover (B).
  17. Disconnect the auto defog sensor connector (A).
    Fig 2: Removing Auto Defog Sensor Cover & Disconnecting Sensor Connector
    G10751076Courtesy of HYUNDAI MOTOR AMERICA
  18. Remove the rain sensor cover (B).
  19. Disconnect the rain sensor connector (A).
    Fig 3: Removing Rain Sensor Cover & Disconnecting Sensor Connector
    G10751077Courtesy of HYUNDAI MOTOR AMERICA
  20. Disconnect the roof trim main connector (A).
    Fig 4: Disconnecting Roof Trim Main Connector
    G10751078Courtesy of HYUNDAI MOTOR AMERICA
  21. Disconnect the hands free mic connector (A).
    Fig 5: Disconnecting Hands Free Mic Connector
    G10751079Courtesy of HYUNDAI MOTOR AMERICA
  22. Detach the clips, then remove the roof trim assembly (A).
    Fig 6: Removing Roof Trim Assembly
    G10751080Courtesy of HYUNDAI MOTOR AMERICA
  23. Remove the room lamp. [Panorama Sunroof type]

    (Refer to "ROOM LAMP ")

  24. Remove the vanity lamp.

    (Refer to "VANITY LAMP ")

  25. Remove the hands free mic.

    (Refer to "HANDS FREE MIC ")

  26. Remove roof trim wiring harness (A) from the roof trim (B).
    NOTE:
    • Take care not to damage the roof trim wiring harness (A) when removing.
    Fig 7: Roof Trim Wiring Harness, Roof Trim & Anti-Noise Pad
    G10751081Courtesy of HYUNDAI MOTOR AMERICA

    Information 

    1. Apply the hot melt continuously when installing the roof trim wiring harness (A) on the roof trim (B) using the hot melt gun tool.
    2. Put anti-noise pad (C) on roof trim (B) to prevent the noise.
  27. Install in the reverse order of removal.

    Information 

    • Make sure the connector is plugged in properly.
    • Replace any damaged clips.
scientia non olet · About LEMON Manuals