Repair procedures: Removal

Remove the following items;
1. Engine cover.
2. Air cleaner assembly and air duct. (Refer to Procedures found in "REPAIR PROCEDURES ")
3. Battery and battery tray.
  (Refer to "CHARGING SYSTEM ")
Remove the ground line after removing the bolt (A).

Fig 1: Ground Line Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).

Fig 2: Solenoid Valve And Inhibitor Switch Connectors
Courtesy of HYUNDAI MOTOR AMERICA
Remove the control cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:

(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)

(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

Fig 3: Removing Control Cable
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Fig 4: Removing Automatic Transaxle Fluid Cooler Hose Clamp
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring clips (A).

Fig 5: Wiring Clips
Courtesy of HYUNDAI MOTOR AMERICA
Remove the solenoid valve connector and inhibitor switch connector wiring mounting bracket (A).

Fig 6: Removing Solenoid Valve Connector And Inhibitor Switch Connector Wiring Mounting Bracket
Courtesy of HYUNDAI MOTOR AMERICA
Using the engine support fixture (beam No.: 09200-38001 or 09200-3N000, supporter No.: 09200-2S000, adapter No.: 09200-4X000), hold the engine and transaxle assembly safely.

Fig 7: Holding Engine And Transaxle Assembly Using Engine Support Fixture
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).
Tightening torque:

(A, B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 8: Removing Automatic Transaxle Upper Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting support bracket bolt (A).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)

Fig 9: Automatic Transaxle Mounting Support Bracket Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Lift the vehicle with a jack.
Remove the under cover (A).
Tightening torque:

6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

Fig 10: Under Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the roll stopper (C) after removing the bolts (A) and (B).

Fig 11: Removing Roll Stopper
Courtesy of HYUNDAI MOTOR AMERICA
Remove the following items.
1. Drive shaft assembly.
  (Refer to "DRIVESHAFT ASSEMBLY ")
Remove the dust cover (A).
Tightening torque:

42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Fig 12: Dust Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the torque converter mounting bolt (A-4ea) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Fig 13: Torque Converter Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle with a jack after removing the mounting bolt (A-1ea, B-3ea).
Tightening torque:

(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

(B) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Fig 14: Automatic Transaxle Lower Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA