Repair procedures: Installation

Temporarily install the transmission assembly to the engine assembly.
Install the mounting bolts (A-2ea) on the transmission.
Tightening torque:

65 ~ 85 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)

Fig 1: Manual Transmission Mounting Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Install the starter motor mounting bolt (A) and nut (B).
Tightening torque:

43 ~ 55 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 2: Starter Motor Mounting Bolt And Nut
Courtesy of HYUNDAI MOTOR AMERICA
Install the mounting bolts (A, B) left in the engine side.
Tightening torque:

[A] 65 ~ 85 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)

[B] 35 ~ 47 N.m (3.5 ~ 4.7 kgf.m, 25.3 ~ 34.0 lb-ft)

Fig 3: Manual Transmission Mounting Bolts (1 Of 2)
Courtesy of HYUNDAI MOTOR AMERICA
Install the mounting bolts (A-4ea) from the engine side.
Tightening torque:

43 ~ 49 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Fig 4: Manual Transmission Mounting Bolts (2 Of 2)
Courtesy of HYUNDAI MOTOR AMERICA
Install the crossmember (A) by installing the bolts (4ea) and put aside the supporting jack.
Tightening torque:

50 ~ 65 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

Fig 5: Crossmember
Courtesy of HYUNDAI MOTOR AMERICA
Install the under shield cover (A).

Fig 6: Under Shield Cover
Courtesy of HYUNDAI MOTOR AMERICA
Install the base bracket (C) and select rod (D) to the transmission with clips (A-2ea) and snap pin (B).

Fig 7: Base Bracket And Select Rod
Courtesy of HYUNDAI MOTOR AMERICA

Fig 8: Clips
Courtesy of HYUNDAI MOTOR AMERICA
Install the propeller shaft to the transmission by installing the bolts (A-3ea).
Tightening torque:

90 ~ 110 N.m (9 ~ 11 kgf.m, 65.1 ~ 79.5 lb-ft)

Fig 9: Propeller Shaft Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Install the clutch hose (A) to the C.S.C assembly.
NOTE: In case of loss of clutch fluid, refill the fluid. (refer to C.S.C ADJUSTMENT PROCEDURE )

Fig 10: Clutch Hose At C.S.C Assembly
Courtesy of HYUNDAI MOTOR AMERICA
Install the CKP sensor (A) by installing a bolt.

Fig 11: CKP Sensor
Courtesy of HYUNDAI MOTOR AMERICA
Connect the back up lamp switch connector.

Fig 12: Back Up Lamp Switch Connector
Courtesy of HYUNDAI MOTOR AMERICA
Connect the oxygen sensor connectors (A, B) from both sides of transmission.

Fig 13: Oxygen Sensor Connector - A
Courtesy of HYUNDAI MOTOR AMERICA

Fig 14: Oxygen Sensor Connector - B
Courtesy of HYUNDAI MOTOR AMERICA
Install the ground wire by installing a bolt.

Fig 15: Ground Wire
Courtesy of HYUNDAI MOTOR AMERICA
Connect (-) terminal to the battery.

Fig 16: Negative Battery Terminal
Courtesy of HYUNDAI MOTOR AMERICA
Refill the transmission fluid.
(Refer to SERVICE ADJUSTMENT PROCEDURE )