Common Specs & Procedures

ELANTRA COUPE COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		SPECIFICATIONS
Torque		Refer to appropriate TORQUE table under WHEN INSTALLING CONNECTING PARTS . Torque specifications are also found in figures, charts and in article text.
Axle Nut/Hub Nut
Front		196.1 ~ 274.5 N.m (20.0 ~ 28.0 kgf.m), 144.6 ~ 202.5 lb-ft)
Rear Hub Bolt		49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4 lb-ft)
Battery
1.8L		Refer to BATTERY SPECIFICATIONS table under CHARGING SYSTEM ;
2.0L		Refer to BATTERY SPECIFICATIONS table under SPECIFICATIONS .
Brakes
Bleeding Sequence		BRAKE SYSTEM BLEEDING
Disc Brakes
	Service Specifications	Refer to SPECIFICATIONS .
	Torque	Refer to TIGHTENING TORQUE . Torque specifications are also found in figures in the DISC BRAKE & DRUM BRAKE SYSTEM article.
Drum Brakes (Drum in Hat)
	Service Specifications	Refer to SPECIFICATIONS . Drum specifications are also found in text in the DISC BRAKE & DRUM BRAKE SYSTEM article.
	Torque	Refer to TIGHTENING TORQUE .
Charging
Generator
	1.8L	Refer to CHARGING SYSTEM ALTERNATOR SPECIFICATIONS table under CHARGING SYSTEM .
	2.0L	Refer to ALTERNATOR SPECIFICATIONS table under SPECIFICATIONS .
Torque
	1.8L	Refer to TIGHTENING TORQUES .
	2.0L	Refer to TIGHTENING TORQUES .
Drive Belts
Adjustment
	1.8L	Refer to procedure under INSTALLATION .
	2.0L	Refer to DRIVE BELT TENSION MEASUREMENT AND ADJUSTMENT .
Drive Belt Routing
	1.8L	Refer to Drive Belt Routing Diagram figure under INSTALLATION .
	2.0L	Refer to Drive Belt Routing Diagram figure under INSTALLATION .
Engine Cooling
General Service Specifications
	1.8L	Refer to COOLING SYSTEM in table under SPECIFICATIONS .
	2.0L	Refer to COOLING SYSTEM in table under SPECIFICATIONS .
	Radiator Cap Pressure	93.16 ~ 122.58 kPa (0.95 ~ 1.25 kgf/cm, 13.51 ~ 17.78 psi).
	Thermostat R & I
	1.8L	Refer to THERMOSTAT .
	2.0L	Refer to THERMOSTAT
	Water Pump R & I
	1.8L	Refer to WATER PUMP .
	2.0L	Refer to WATER PUMP .
Engine Mechanical
	Compression
	1.8L	Standard: 1,275 kPa (13.0 kgf/cm, 185 psi); Minimum pressure: 1,128 kPa (11.5 kgf/cm, 164 psi); Difference between cylinders: 100 kPa (1.0 kgf/cm, 15 psi) or less.
	2.0L	Standard: 1,373 kPa (14.0 kgf/cm, 199 psi); Minimum pressure: 1,226 kPa (12.5 kgf/cm, 178 psi); Difference between cylinders: 100 kPa (1.0 kgf/cm, 15 psi) or less.
Oil pressure		98.07 kPa (1.0 kgf/cm, 14.22 psi) or above @ 1000 RPM
Overhaul
	1.8L	Refer to SPECIFICATIONS .
	2.0L	Refer to SPECIFICATIONS .
	Torque
	1.8L	Refer to TIGHTENING TORQUES .
	2.0L	Refer to TIGHTENING TORQUES .
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque		117.7 ~ 127.5 N.m (12.0 ~ 13.0 kgf.m, 86.8 ~ 94.0 lb-ft)
Fuel System
Pressure Specification		324 ~ 363 kPa (3.3 ~ 3.7 kgf/cm, 46.9 ~ 52.6 psi)
	Fuel Pressure Test Procedure
	1.8L	Refer to FUEL PRESSURE TEST .
	2.0L	Refer to FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) .
	Fuel Filter Location	Fuel filter is part of fuel pump assembly.
	Fuel Filter R & I
	1.8L	Refer to REPAIR PROCEDURES .
	2.0L	Refer to REPAIR PROCEDURES .
Ignition
Firing Order & Cylinder Identification		Refer to FIRING ORDER & CYLINDER IDENTIFICATION .
Ignition Wires (Resistance)		Coil-On
Ignition Wires (Routing)		Coil-On
Spark Plug
Type		SILZKR7B11
Gap		1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in.)
Torque		14.7 ~ 24.5 N.m (1.5 ~ 2.5 kgf.m, 10.8 ~ 18.1 lb-ft)
Starting
Starter
	1.8L	Refer to SPECIFICATION .
	2.0L	Refer to SPECIFICATION .
Torque		49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Wheel Alignment
	Adjustment Specifications	Refer to WHEEL ALIGNMENT .
	Torque	Refer to TIGHTENING TORQUES .
Wheel & Tire
Wheel Lug Nut Torque		88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)