Tightening Torques
TIGHTENING TORQUES
| Items | Nm | kgf.cm | lb-ft | |
|---|---|---|---|---|
| Oil pan bolt | 10 - 12 | 100 - 120 | 7 - 8 | |
| Select lever assembly mounting bolt | 9 - 14 | 90 - 140 | 6.5 - 10 | |
| Starter motor mounting bolt | 27 - 34 | 270 - 340 | 19 - 24 | |
| Oil cooler hose connector | 15 - 22 | 150 - 220 | 11 - 16 | |
| Hose bracket | 3 -5 | 30 - 50 | 2 - 4 | |
| Bell housing cover to engine | 8 - 10 | 80 - 100 | 6 - 7 | |
| Transaxle mounting lower bolt (dia. 10 mm) | 43 - 55 | 430 - 550 | 32 - 41 | |
| Transaxle mounting upper bolt (dia. 12 mm) | 60 - 80 | 600 - 800 | 43 - 58 | |
| Torque converter mounting bolt | 46 - 53 | 460 - 530 | 33 - 38 | |
| Control cable to body | 8 - 11 | 80 - 110 | 6 - 7.5 | |
| Lever assembly to bracket assembly | 14 - 22 | 140 - 220 | 10 - 16 | |
| Oil drain plug | 35 - 45 | 350 - 450 | 25 - 32 | |
| Pressure check plug | 8 - 10 | 80 - 100 | 6 - 7 | |
| Pulse generator | 10 - 12 | 100 - 120 | 7 - 8 | |
| Bearing retainer | 17 - 22 | 170 - 220 | 13 - 16 | |
| Transfer drive gear | 16 - 21 | 160 - 210 | 12 - 15 | |
| One-way clutch inner race | 35 - 45 | 350 - 450 | 25 - 32 | |
| Differential drive gear | 130 - 140 | 1300 - 1400 | 94 - 101 | |
| Manual control lever | 17 - 21 | 170 - 210 | 13 - 15 | |
| Manual control shaft lock screw | 8 - 10 | 80 - 100 | 6 - 7 | |
| Inhibitor switch | 10 - 12 | 100 - 120 | 7 - 8 | |
| Sprag rod support bolt | 20 - 27 | 200 - 270 | 14 - 19 | |
| Pump housing to reaction shaft support bolt | 10 - 12 | 100 - 120 | 7 - 8 | |
| Oil pump assembly mounting bolt | 19 - 23 | 190 - 230 | 14 - 17 | |
| Valve body cover | 10 - 12 | 100 - 120 | 7 - 8 | |
| Valve body assembly mounting bolt | 10 - 12 | 100 - 120 | 7 - 8 | |
| Oil filter | 5 - 7 | 50 - 70 | 4 - 5 | |
| Speedometer driven gear sleeve | 3 - 5 | 30 - 50 | 2 - 4 | |
| Kickdown adjusting screw | 15 - 22 | 150 - 220 | 11 - 15 | |
| End cover bolt | 19 - 23 | 190 - 230 | 14 - 17 | |
| Differential cover | M8 | 20 - 27 | 200 - 270 | 14 - 19 |
| M10 | 43 - 55 | 430 - 550 | 32 - 41 | |
| Differential bearing cap | 60 - 80 | 600 - 800 | 43 - 58 | |
| Differential bearing retainer | 43 - 55 | 430 - 550 | 32 - 41 | |
| Locking nut (M38) - Input | 180 - 210 | 1800 - 2100 | 130 - 152 | |
| Locking nut - Output | 200 - 230 | 2000 - 2300 | 146 - 166 | |
| Shift cable bracket bolt | 19 - 23 | 190 - 230 | 14 - 17 | |
| Rear roll supt bracket | M12 | 60 - 80 | 600 - 800 | 43 - 58 |