Battery Test Procedure

Connect the tester to the battery.
1. Red clamp to battery positive (+) terminal.
2. Black clamp to battery negative (-) terminal.
  
  Fig 1: Testing Battery
  Courtesy of HYUNDAI MOTOR CO.
  
  CAUTION: Connect clamps securely. If "CHECK CONNECTION" message is displayed on the screen, reconnect clamps securely.
The tester will ask if the battery is connected "IN-VEHICLE" or "OUT-OF-VEHICLE". Make your selection by pressing the arrow buttons; then press ENTER.

Fig 2: Display - IN-VEHICLE
Courtesy of HYUNDAI MOTOR CO.
Select CCA and press the ENTER button.

Fig 3: Display - CCA
Courtesy of HYUNDAI MOTOR CO.

NOTE: CCA : Cold cranking amps, is an SAE specification for cranking batteries at -0.4 °F (-18 °C).
Set the CCA value displayed on the screen to the CCA value marked on the battery label by pressing up and down buttons and press ENTER.

Fig 4: Display - CCA Value
Courtesy of HYUNDAI MOTOR CO.

NOTE: The battery ratings (CCA) displayed on the tester must be identical to the ratings marked on battery label.
The tester will conduct battery test.

Fig 5: Display - Battery Testing
Courtesy of HYUNDAI MOTOR CO.

The tester displays battery test results including voltage and battery ratings.

Refer to the following table and take the appropriate action as recommended by the Micro 570.

Fig 6: Display - Battery Test Result

Courtesy of HYUNDAI MOTOR CO.

Battery Test Results

BATTERY TEST RESULTS

Result On Printer	Remedy
GOOD BATTERY	No action is required
GOOD RECHARGE	Battery is in a good state Recharge the battery and use
CHARGE & RETEST	Battery is not charged properly Charge and test the battery again. (Failure to charge the battery fully may read incorrect measurement value)
REPLACE BATTERY	Replace battery and recheck the charging system. Improper connection between battery and vehicle cables may cause "REPLACE BATTERY", retest the battery after removing cables and connecting the tester to the battery terminal directly prior to replacing the battery.
BAD CELL-REPLACE	Charge and retest the battery. If the Micro 570 recommends "REPLACE BATTERY", replace the battery and recheck the charging system.

WARNING: Whenever filing a claim for battery, the print out of the battery test results must be attached.

Starter Test Procedure

After the battery test, press ENTER immediately for the starter test.

Fig 7: Display - Starter Test
Courtesy of HYUNDAI MOTOR CO.
Start the engine.

Fig 8: Display - Start Engine
Courtesy of HYUNDAI MOTOR CO.

Cranking voltage and starter test results will be displayed on the screen.

Refer to the following table and take the appropriate action as recommended by the Micro 570.

Fig 9: Display - Cranking Voltage And Starter Test Result

Courtesy of HYUNDAI MOTOR CO.

Starter Test Results

STARTER TEST RESULTS

Result On Printer	Remedy
CRANKING VOLTAGE NORMAL	System shows a normal starter draw
CRANKING VOLTAGE LOW	Cranking voltage is lower than normal level Check starter
CHARGE BATTERY	The state of battery charge is too low to test Charge the battery and retest
REPLACE BATTERY	Replace battery If the vehicle is not started though the battery condition of "GOOD BATTERY" is displayed, check wiring for open circuit, battery cable connection, starter and repair or replace as necessary. If the engine does crank, check fuel system.

NOTE: When testing the vehicle with old diesel engines, the test result will not be favorable if the glow plug is not heated. Conduct the test after warming up the engine for 5 minutes.

Charging System Test Procedure

Press ENTER to begin charging system test.

Fig 10: Display - ENTER To Begin Charging System Test
Courtesy of HYUNDAI MOTOR CO.
The tester displays the actual voltage of alternator.
Press ENTER to continue.

Fig 11: Display - Actual Voltage Of Alternator
Courtesy of HYUNDAI MOTOR CO.
Turn off all electrical load and rev engine for 5 seconds with pressing the accelerator pedal. (Follow the instructions on the screen)

Fig 12: Display - Turn OFF Electrical Load And REV Engine For 5 Seconds
Courtesy of HYUNDAI MOTOR CO.

Fig 13: Display - INCREASE REV
Courtesy of HYUNDAI MOTOR CO.

Fig 14: Display - HOLD REV
Courtesy of HYUNDAI MOTOR CO.
The message that engine RPM is detected will be displayed on the screen. Press ENTER to continue.

Fig 15: Display - RPM Detected
Courtesy of HYUNDAI MOTOR CO.
If the engine RPM is not detected, press ENTER after revving engine.

Fig 16: Display - ENTER For After Revving Engine
Courtesy of HYUNDAI MOTOR CO.
The tester will conduct charging system test during loads off.

Fig 17: Display - Charging System Test (1 Of 2)
Courtesy of HYUNDAI MOTOR CO.

Fig 18: Display - Charging System Test (2 Of 2)
Courtesy of HYUNDAI MOTOR CO.
Turn on electrical loads (air conditioner, lamps, audio and etc.). Press ENTER to continue.

Fig 19: Display - Turn Loads ON
Courtesy of HYUNDAI MOTOR CO.
The tester will conduct charging system test during loads on.

Fig 20: Display - Charging System Test During Loads ON
Courtesy of HYUNDAI MOTOR CO.
Rev engine for 5 seconds with pressing the accelerator pedal. (Follow the instructions on the screen)

Fig 21: Display - REV Engine For 5 Second
Courtesy of HYUNDAI MOTOR CO.

Fig 22: Display - INCREASE REV
Courtesy of HYUNDAI MOTOR CO.

Fig 23: Display - HOLD REV
Courtesy of HYUNDAI MOTOR CO.
The message that engine RPM is detected will be displayed on the screen. Press ENTER to continue.

Fig 24: Display - RPM Detected Message
Courtesy of HYUNDAI MOTOR CO.
If the engine RPM is not detected, press ENTER after revving engine.

Fig 25: Display - ENTER To Cont After Revving Engine
Courtesy of HYUNDAI MOTOR CO.
Turn off electrical loads (air conditioner, lamps, audio and etc.). Turn the engine off.

Fig 26: Display - Turn Loads OFF
Courtesy of HYUNDAI MOTOR CO.

Charging voltage and charging system test results will be displayed on the screen.

Shut off engine end disconnect the tester clamps from the battery. Refer to the following table and take the appropriate action as recommended by the Micro 570.

Fig 27: Display - Charging Voltage And Charging System Test Result

Courtesy of HYUNDAI MOTOR CO.

Fig 28: Display - Diode Ripple Normal

Courtesy of HYUNDAI MOTOR CO.

Fig 29: Display - Charging System Normal

Courtesy of HYUNDAI MOTOR CO.

Charging System Test Results

CHARGING SYSTEM TEST RESULTS

Result On Printer	Remedy
CHARGING SYSTEM NORMAL/DIODE RIPPLE NORMAL	Charging system is normal
NO CHARGING VOLTAGE	Alternator does not supply charging current to battery Check belts, connection between alternator and battery and replace belts or cable or alternator as necessary
LOW CHARGING VOLTAGE	Alternator does not supply charging current to battery and electrical load to system fully Check belts and alternator and replace as necessary
HIGH CHARGING VOLTAGE	The voltage from alternator to battery is higher than normal limit during voltage regulating. Check connection and ground and replace regulator as necessary Check electrolyte level in the battery
EXCESS RIPPLE DETECTED	One or more diodes in the alternator is not functioning properly Check alternator mounting and belts and replace as necessary