Torque Specifications
TIGHTENING TORQUE SPECIFICATION (A/T)
| Item | Nm | kg.cm | lb.ft |
|---|---|---|---|
| Wiring harness bracket | 20-26 | 200-260 | 14-18 |
| Control cable bracket bolt | 20-26 | 200-260 | 14-18 |
| Fluid temperature sensor | 27-33 | 270-330 | 19-23 |
| Eye bolt | 10-12 | 100-120 | 7-8 |
| Oil cooler feed tube | 11-13 | 110-130 | 8-9 |
| Oil filter | 10-12 | 100-120 | 7-8 |
| Input shaft speed sensor | 10-12 | 100-120 | 7-8 |
| Output shaft speed sensor | 18-25 | 180-250 | 13-18 |
| Manual control lever | 10-12 | 100-120 | 7-8 |
| Transaxle range switch | 4-6 | 40-60 | 3-4 |
| Speedometer gear | 8-10 | 80-100 | 6-7 |
| Valve body cover | 10-12 | 100-120 | 7-8 |
| Valve body mounting bolt | 10-12 | 100-120 | 7-8 |
| Manual control shaft detent | 5-7 | 50-70 | 4-5 |
| Rear cover | 20-26 | 200-260 | 14-18 |
| Torque converter housing | 42-54 | 420-540 | 29-38 |
| Oil pump | 20-261 | 200-260 | 14-18 |
| Transfer drive gear | 6-22 | 160-220 | 11-15 |
| Output shaft lock nut | 160-180 | 1600-1800 | 110-126 |
| Output shaft bearing retainer | 20-26 | 200-260 | 14-18 |
| Oil filler plug | 29-34 | 290-340 | 20-24 |
| Oil drain plug | 29-34 | 290-340 | 20-24 |
| Transfer drive gear lock nut | 180-210 | 1800-2100 | 126-147 |
| Differential drive gear to subframe bolts | 130-140 | 1300-1400 | 91-98 |
| Valve body | 10-12 | 100-120 | 7-8 |
| Solenoid valve support | 5-7 | 50-70 | 4-5 |
| Plate | 5-7 | 50-70 | 4-5 |
| Pressure check plug | 8-10 | 80-100 | 6-7 |
| Front roll stopper bracket to subframe bolts | 40-55 | 400-550 | 29-38 |
| Front roll stopper insulator bolt and nut | 50-65 | 500-650 | 36-47 |
| Front roll stopper bracket to transaxle bolts | 60-80 | 600-800 | 43-58 |
| Rear roll stopper bracket | 40-55 | 400-550 | 29-38 |
| Rear roll stopper insulator bolt and nut | 50-60 | 500-650 | 36-47 |
| Rear roll stopper bracket to transaxle bolts | 60-80 | 600-800 | 43-58 |
| Transfer case assembly to transaxle mounting bolt | 64-70 | 640-700 | 47-51 |
| Transfer case bracket bolt | 24-28 | 240-280 | 17-20 |
| Transfer case assembly to engine block | 50-54 | 500-540 | 36-39 |
| Transfer case oil drain plug | 34-38 | 340-380 | 25-28 |
| Transfer case oil filler plug | 34-38 | 340-380 | 25-28 |
| Transfer case flange bolt | 34-37 | 340-370 | 25-28 |
| Pinion case flange bolt | 34-37 | 340-370 | 25-28 |
| Transaxle mounting sub bracket nut | 60-80 | 600-800 | 43-58 |
| Transaxle mounting bracket bolts | 40-55 | 400-550 | 29-38 |
| Transaxle mounting insulator bolt | 90-110 | 900-1100 | 65-80 |