LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2003 >> Santa Fe Base, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (3.5L V6 Engine) >> General >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS

Application Ft. Lbs (N.m)
Auto Tensioner Fixed Bolt 15-20 (20-27)
Camshaft Bearing Cap
Inner (1)
Outer 14-15 (19-20)
Camshaft Sprocket Bolt 59-81 (80-110)
Connecting Rod Nut
Step 1 26 (35)
Step 2 Tighten An Additional 90 Degrees
Coolant Inlet Fitting Bolt 13-15 (17-20)
Coolant Pump Bolt
M8 Bolt Head Mark "7" 11-16 (15-22)
M10 24-37 (33-50)
Coolant Temperature Sensor 15-30 (20-40)
Crankshaft Bolt 133-140 (180-190)
Cylinder Head Bolt (Cold) (2) 77-85 (105-115)
Drive Plate & Adapter Plate Bolt 54-57 (73-77)
Drive Belt Pulley Bolt 26-41 (35-55)
Engine Hanger Bracket Bolt 20-28 (27-38)
Engine Mounting Fasteners
Engine Mounting Bracket Bolt 44-59 (60-80)
Engine Mounting Bracket Nut 44-59 (60-80)
Engine Mounting Insulator Bolt 66-81 (90-110)
Front Roll Stopper Bracket-To-Transaxle Bolt 44-59 (60-80)
Front Roll Stopper Insulator Fasteners 37-48 (50-65)
Front Roll Stopper Bracket-To-Subframe Bolt 44-59 (60-80)
Rear Roll Stopper Bracket-To-Subframe Bolts 44-59 (60-80)
Rear Roll Stopper Bracket-To-Transaxle Bolts 37-48 (50-65)
Rear Roll Stopper Insulator Bolt & Nut 37-48 (50-65)
Exhaust Components
Catalytic Converter-To-Center Exhaust Pipe Nut 22-30 (30-40)
Center Exhaust Pipe-To-Main Muffler Nuts 22-30 (30-40)
Exhaust Manifold-To-Engine Bolt 30-33 (40-45)
Front Exhaust Pipe-To-Catalytic Converter Bolt 30-44 (40-60)
Front Exhaust Pipe-To-Exhaust Manifold Nuts 22-30 (30-40)
Exhaust Manifold-To-Cylinder Head Nut 30-33 (40-45)
Generator Mounting Bracket Bolt (All) 15-22 (20-30)
Intake Manifold-To-Cylinder Head Nuts 15-17 (20-23)
Main Bearing Bolt 52-59 (70-80)
Oil Drain Plug 26-33 (35-45)
Oil Filter 9-12 (12-16)
Oil Pump Case Bolt 11-15 (15-20)
Oil Pump Relief Valve Plug 30-37 (40-50)
Oil Screen Bolt 11-16 (15-22)
Oxygen Sensor 30-37 (40-50)
Power Steering Bracket-To-Cylinder Head Bolt 13-19 (17-26)
Power Steering Pump-To-Bracket bolt 13-19 (17-26)
Starter-To-Engine
Bolt 20-25 (27-34)
Nut 15-22 (20-30)
Surge Tank Stay Bolt 11-15 (15-20)
Throttle Body-To-Surge Tank Bolts 15-18 (20-25)
Transaxle Mounting Fasteners
Transaxle Mounting Bracket Bolts 44-59 (60-80)
Transaxle Mounting Sub Bracket Nut 44-59 (60-80)
Transaxle Mounting Insulator Bolt 66-81 (90-110)
Timing Belt Cover Bolt (8 mm) 15-20 (20-27)
Timing Belt Idler Pulley Bolt 37-44 (50-60)
Timing Belt Tensioner Arm Fixed Bolt 26-41 (35-55)
Timing Belt Tensioner Bolt 15-20 (20-27)
Timing Belt Tensioner Pulley Bolt 32-41 (43-55)
Upper Oil Pan Bolt
10x38 mm 22-31 (30-42)
6x18 mm (3)
6x161.55 mm (3)
6x152.5 mm (3)
Water Outlet Fitting Bolt 13-15 (17-20)
INCH Lbs. (N.m) 
Air Cleaner Body Installation Bolt 71-106 (8-12)
Air Cleaner Mounting Bolt 71-106 (8-12)
Crankshaft Position Sensor Wheel Screw 97-106 (11-12)
Cylinder Head Cover Bolt 71-88 (8-10)
Delivery Pipe Installation Bolt 89-133 (10-15)
Fuel Hose Clamp-To-Engine Bolt 106-133 (12-15)
Generator Inlet Pipe-To-Front Cylinder Head Assembly 106-133 (12-15)
Heat Protector-To-Exhaust Manifold 106-133 (12-15)
Lower Oil Pan Bolt 89-106 (10-12)
Main Muffler Hanger Support Bracket Bolt 89-133 (10-15)
Oil Level Guide-To-Engine 106-133 (12-15)
Oil Pressure Switch 71-133 (8-15)
Oil Pump Cover Screw 71-106 (8-12)
Oil Seal Case 89-106 (10-12)
Rear Plate 89-106 (10-12)
Timing Belt Cover Bolt (6 mm) 89-106 (10-12)
Transaxle Mounting Plate 89-106 (10-12)
(1) Tighten to 89-106 INCH Lbs. (10-12 N.m).
(2) Tighten cylinder head bolts in sequence. See Fig 1.
(3) Tighten to 44-62 INCH Lbs. (5-7 N.m).
Fig 1: Identifying Cylinder Head Bolt Tightening Sequence
G00240113Courtesy of HYUNDAI MOTOR CO.