Torque Specifications
WARNING: This page is about a different variant/trim than selected.
WARNING:
For updated reuse guidelines and tightening procedures of cylinder head, connecting rod and main bearing bolts, refer to TSB 02-20-002 CYLINDER HEAD/CONNECTING ROD/MAIN BEARING BOLT REUSE GUIDELINES & TORQUE SPECS
.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |||||
|---|---|---|---|---|---|---|
| Alternator Mounting Bracket-To-Engine | 15-20 (20-27) | |||||
| Alternator Mounting Bolt | 15-20 (20-27) | |||||
| Alternator Mounting Nut | 15-20 (20-27) | |||||
| Air Intake Surge Tank | ||||||
| Mounting Bolt/Nut | 11-15 (15-20) | |||||
| Surge Tank Stay | 11-15 (15-20) | |||||
| Auto Tensioner Arm Fixed Bolt | 26-41 (35-55) | |||||
| Camshaft Sprocket Bolt | 66-81 (90-110) | |||||
| Coolant Inlet Fitting Bolt | 13-15 (17-20) | |||||
| Coolant Pump-To-Engine Bolt | 11-16 (15-22) | |||||
| Coolant Temperature Sensor | 15-30 (20-40) | |||||
| Connecting Rod Cap Bolt | ||||||
| Step 1 | 13 (18) | |||||
| Step 2 | Tighten An Additional 90 Degrees | |||||
| Crankshaft | ||||||
| Main Bearing Cap Bolt | ||||||
| M8 Bolt | ||||||
| Step 1 | 12 (16) | |||||
| Step 2 | Tighten An Additional 90 Degrees | |||||
| M10 Bolt | ||||||
| Step 1 | 22 (30) | |||||
| Step 2 | Tighten An Additional 90 Degrees | |||||
| Pulley Bolt | 133-140 (180-190) | |||||
| Cylinder Head Bolt (1) | ||||||
| Step 1 | 18 (25) | |||||
| Step 2 | Tighten An Additional 60 Degrees | |||||
| Step 3 | Tighten An Additional 45 Degrees | |||||
| Drive Belt Pulley Bolt | 26-41 (35-55) | |||||
| Drive Belt Tensioner Bolt | 15-20 (20-27) | |||||
| Drive Plate & Adaptor Bolt | 54-57 (73-77) | |||||
| Engine Mounts | ||||||
| Engine Hanger Bracket-To-Engine | 15-20 (20-27) | |||||
| Engine Mounting Bracket Bolt | 44-59 (60-80) | |||||
| Engine Support Bracket Stud | 22-30 (30-40) | |||||
| Engine Mounting Bracket Nut | 44-59 (60-80) | |||||
| Engine Mounting Insulator Bolt | 30-41 (40-55) | |||||
| Front Roll Stopper Bracket-To-Subframe Bolt | 30-41 (40-55) | |||||
| Front Roll Stopper Insulator Bolt & Nut | 37-48 (50-65) | |||||
| Rear Roll Stopper Insulator Bolt & Nut | 30-41 (40-55) | |||||
| Transaxle Mount | ||||||
| Bracket Bolt/Nut | 30-41 (40-55) | |||||
| Insulator Bolt | 66-81 (90-110) | |||||
| Exhaust Manifold-To-Cylinder Head Nut | 18-22 (25-30) | |||||
| Exhaust Pipe | ||||||
| Catalytic Converter-To-Center Exhaust Pipe Nut | 22-30 (30-40) | |||||
| Center Exhaust Pipe-To-Main Muffler Nut | 22-30 (30-40) | |||||
| Pipe-To-Manifold Nut | 22-30 (30-40) | |||||
| Pipe-To-Catalytic Converter Bolt | 30-44 (40-60) | |||||
| Flywheel Bolt | 54-57 (73-77) | |||||
| Intake Manifold Mounting Bolt/Nut | 14-15 (19-20) | |||||
| Oil Filter | 9-12 (12-16) | |||||
| Oil Pan Bolt | ||||||
| Lower Pan | 89-106 INCH Lbs. (10-12) | |||||
| Upper Pan | ||||||
| 10x38 mm | 22-31 (30-42) | |||||
| 8x22 mm | 14-21 (19-28) | |||||
| 171.5 mm | 44-62 INCH Lbs. (5-7) | |||||
| 152.5 mm | 44-62 INCH Lbs. (5-7) | |||||
| Oil Pan Drain Plug | 26-33 (35-45) | |||||
| Oil Pan Screen Bolt | 11-16 (15-22) | |||||
| Oil Pressure Switch | 11-16 (15-22) | |||||
| Oil Pump | ||||||
| Driven Gear Bolt | 25-29 (34-39) | |||||
| Relief Valve Plug | 30-37 (40-50) | |||||
| Sprocket Nut | 35-43 (48-58) | |||||
| Oxygen Sensor | 30-37 (40-50) | |||||
| Power Steering Pump Bracket-To-Cylinder Head Bolt | 13-19 (17-26) | |||||
| Power Steering Pump-To-Bracket Bolt | 13-19 (17-26) | |||||
| Spark Plug | 15-22 (20-30) | |||||
| Starter | ||||||
| Bolt | 20-25 (27-34) | |||||
| Nut | 14-22 (19-30) | |||||
| Thermostat Housing | 13-15 (17-20) | |||||
| Throttle Body-To-Surge Tank Bolt | 11-15 (15-20) | |||||
| Timing Belt Assembly | ||||||
| Auto Tensioner Fixed Bolt | 14-20 (19-27) | |||||
| Auto Tensioner Pulley Bolt | 32-41 (43-55) | |||||
| Idler Pulley Bolt | 37-44 (50-60) | |||||
| Tensioner Arm Fixed Bolt | 26-41 (35-55) | |||||
| INCH Lbs. (N.m) | ||||||
| Accelerator Bracket Bolt | 35-53 (4-6) | |||||
| Air Cleaner Body Bolt | 71-106 (8-12) | |||||
| Crank Position Sensor | 44-53 (5-6) | |||||
| Cylinder Head Cover Bolts | 44-53 (5-6) | |||||
| Delivery Pipe Installation Bolt | 89-133 (10-15) | |||||
| Exhaust Manifold Heat Shield Bolt | 106-133 (12-15) | |||||
| Fuel Hose Clamp-To-Cylinder Head Bolt | 106-133 (12-15) | |||||
| Main Muffler Hanger Support Bracket Bolt | 89-133 (10-15) | |||||
| Oil Level Gauge Guide Bolt | 106-133 (12-15) | |||||
| Oil Pump | ||||||
| Case Bolt | 106-133 (12-15) | |||||
| Cover Screw | 71-106 (8-12) | |||||
| Oil Seal Case Bolt | 89-106 (10-12) | |||||
| Rear Plate | 89-106 (10-12) | |||||
| Transaxle Mounting Plate | 89-106 (10-12) | |||||
| Timing Belt Assembly Cover Bolt | 89-106 (10-12) | |||||
|
||||||