LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2000 >> Sonata GLS, Automatic >> Repair and Diagnosis >> Engine Mechanical >> Lubrication System >> 2.5L V6 Engine >> Torque Specifications

Torque Specifications

WARNING: For updated reuse guidelines and tightening procedures of cylinder head, connecting rod and main bearing bolts, refer to TSB 02-20-002 CYLINDER HEAD/CONNECTING ROD/MAIN BEARING BOLT REUSE GUIDELINES & TORQUE SPECS .
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Air Intake Surge Tank
Mounting Bolt/Nut 11-14 (15-19)
Auto Tensioner Arm Bolt 26-40 (35-54)
Camshaft Sprocket Bolt 65-80 (88-108)
Connecting Rod Cap Bolt
Step 1 13 (18)
Step 2 Additional 90 Degrees
Crankshaft
Main Bearing Cap Bolt
M8 Bolt
Step 1 12 (16)
Step 2 Additional 90 Degrees
M10 Bolt
Step 1 22 (30)
Step 2 Additional 90 Degrees
Pulley Bolt 130-138 (176-187)
Cylinder Head Bolt (1)
Step 1 18 (25)
Step 2 Additional 60 Degrees
Step 3 Additional 45 Degrees
Engine Mounts
Insulator Bolt 65-80 (88-108)
Bracket Bolt/Nut 43-58 (58-79)
Front Roll Stopper
Bracket-To-Subframe Bolt 43-58 (58-79)
Bracket-To-Transaxle Bolt 43-58 (58-79)
Insulator Bolt/Nut 36-47 (49-64)
Rear Roll Stopper
Bracket-To-Subframe Bolt 43-58 (58-79)
Bracket-To-Transaxle Bolt 36-47 (49-64)
Insulator Bolt/Nut 36-47 (49-64)
Transaxle Mount
Bracket Bolt/Nut 43-58 (58-79)
Insulator Bolt 65-80 (88-108)
Exhaust Manifold-To-Cylinder Head Nut 18-22 (24-30)
Exhaust Pipe
Pipe-To-Manifold Nut 22-29 (30-39)
Pipe-To-Catalytic Converter Bolt 29-43 (39-58)
Flywheel-To-Crankshaft Bolt 53-55 (72-75)
Intake Manifold Mounting Bolt/Nut 14-15 (19-20)
Oil Pan Drain Plug 26-32 (35-43)
Oil Pan Screen Bolt 11-15 (15-20)
Oil Pump
Driven Gear Bolt 25-29 (34-39)
Relief Valve Plug 29-36 (39-48)
Sprocket Nut 36-43 (48-58)
Starter
Bolt 20-25 (27-34)
Nut 14-22 (19-30)
Thermostat Housing 11-14 (15-19)
Throttle Body-To-Intake Manifold Bolt 11-15 (15-20)
Timing Belt Assembly
Auto Tensioner Fixed Bolt 14-20 (19-27)
Auto Tensioner Pulley Bolt 31-40 (42-540
Idler Pulley Bolt 36-43 (48-58)
Water Pump Mounting Bolt 11-16 (15-22)
INCH Lbs. (N.m) 
Camshaft Bearing Cap Bolt 89-106 (10-12)
Cylinder Head Cover Bolts 44-53 (5-6)
Exhaust Manifold Heat Shield Bolt 106-133 (12-15)
Oil Pan Bolt
Lower Pan 89-106 (10-12)
Upper Pan (2)
Oil Pressure Switch 71-106 (8-12)
Oil Pump
Case Bolt 106-133 (12-15)
Cover Screw 71-106 (8-12)
Rear Oil Seal Case Bolt 89-106 (10-12)
Timing Belt Assembly Cover Bolt 89-106 (10-12)
Water Pump Pulley Bolt 71-89 (8-10)
(1) Tighten in sequence with engine cold. See Figure.
(2) See OIL PUMP  under REMOVAL & INSTALLATION for bolt identification and tightening specifications.