LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2007 >> H3 Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 31 (Supplemental Inflatable Restraint System) >> Repair Instructions >> SIR Disabling and Enabling Zone 8 >> Enabling Procedure

Enabling Procedure

WARNING: This page is about a different car, the 2005 GMC Canyon and 2005 Chevrolet Colorado. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the key from the ignition.
    2. Fig 1: View Of Steering Wheel Module Yellow 4-Way Connector & Connector Position Assurance
    GM869638Courtesy of GENERAL MOTORS CORP.
  2. Connect the steering wheel module yellow 4-way connector (1) located left of the steering column (2) above the left hinge pillar trim panel.
  3. Install the CPA (1) to the steering wheel module yellow 4-way connector (1) located left of the steering column (2) above the left hinge pillar trim panel.
    4. Fig 2: View Of Roof Rail Module Connector
    GM1276857Courtesy of GENERAL MOTORS CORP.
  4. Connect the roof rail module connector (1) and install the garnish molding. Refer to Garnish Molding Replacement - Windshield Pillar in Interior Trim.
    5. Fig 3: View Of Seat Belt Retractor/Pretensioner Assembly
    GM1276832Courtesy of GENERAL MOTORS CORP.
  5. Connect the seat belt pretensioner - left and install the CPA.
  6. Install the trim panel. Refer to Trim Panel Replacement - Body Rear Corner - Lower (Crew Cab) or Trim Panel Replacement - Body Rear Corner - Lower (Regular Cab) or Trim Panel Replacement - Body Rear Corner - Lower (Extended Cab) for regular cab or Trim Panel Replacement - Lower Center Pillar for crew cab in Interior Trim. For extended cab install the rear access door wiring harness grommet.
    7. Fig 4: View Of Connector Position Assurance (CPA) & Side Impact Sensor Yellow 2-Way Connector
    GM612189Courtesy of GENERAL MOTORS CORP.
  7. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  8. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  9. Install the left door trim panel. Refer to Trim Panel Replacement - Side Front Door in Doors.
    10. Fig 5: View Of Connector Position Assurance (CPA) & Steering Wheel Module Yellow 4-Way Connector
    GM819731Courtesy of GENERAL MOTORS CORP.
  10. Connect the I/P module yellow 4-way inline connector C208 (2) located above the driver door kick panel.
  11. Install the CPA to the I/P module yellow 4-way inline connector C208 (2) located above the driver side kick panel.
    12. Fig 6: View Of Roof Rail Module Connector
    GM1276857Courtesy of GENERAL MOTORS CORP.
  12. Connect the roof rail module connector (1) and install the garnish molding. Refer to Garnish Molding Replacement - Windshield Pillar in Interior Trim.
    13. Fig 7: View Of Seat Belt Retractor/Pretensioner Assembly
    GM1276832Courtesy of GENERAL MOTORS CORP.
  13. Connect the seat belt pretensioner-right and install the CPA.
  14. Install the trim panel. Refer to Trim Panel Replacement - Body Rear Corner - Lower (Crew Cab) or Trim Panel Replacement - Body Rear Corner - Lower (Regular Cab) or Trim Panel Replacement - Body Rear Corner - Lower (Extended Cab) for regular cab or Trim Panel Replacement - Lower Center Pillar for crew cab in Interior Trim. For extended cab install the rear access door wiring harness grommet.
    15. Fig 8: View Of Connector Position Assurance (CPA) & Side Impact Sensor Yellow 2-Way Connector
    GM612189Courtesy of GENERAL MOTORS CORP.
  15. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  16. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  17. Install the left door trim panel. Refer to Trim Panel Replacement - Side Front Door in Doors.
    18. Fig 9: Locating SIR Fuse
    GM1293224Courtesy of GENERAL MOTORS CORP.
  18. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  19. Staying well away from all air bags, turn ON the ignition, with the engine OFF.
    1. The AIR BAG indicator will flash 7 times.
    2. The AIR BAG indicator will then turn OFF.
  20. Perform the Diagnostic System Check - Vehicle in Vehicle DTC Information, if the AIR BAG indicator does not operate as described.
scientia non olet · About LEMON Manuals