| ATF pressure |
Line pressure (low) |
APP Sensor opening less than 25 % in D with Line Pressure |
662-711 kPa (6.75-7.25 kgf/cm2, 96.0-103.1 psi) |
Lower limit: 662 kPa (6.75 kgf/cm 2, 96.0 psi) Upper limit: 711 kPa (7.25 kgf/cm 2, 103.1 psi) |
| Line pressure (normal) |
At 2, 000 rpm in N or P |
1, 123-1, 172 kPa (11.45-11.95 kgf/cm 2, 162.9-170.0 psi) |
1, 079 kPa (11.00 kgf/cm 2, 156.5 psi) |
| Clutch pressure (1st) |
At idle speed |
1, 123-1, 172 kPa (11.45-11.95 kgf/cm 2, 162.9-170.0 psi) |
1, 079 kPa (11.00 kgf/cm 2, 156.5 psi) |
| Clutch pressure (2nd-6th) |
At 2, 000 rpm in each gears |
1, 123-1, 172 kPa (11.45-11.95 kgf/cm 2, 162.9-170.0 psi) |
1, 079 kPa (11.00 kgf/cm 2, 156.5 psi) |
| Torque converter clutch pressure |
At 2, 000 rpm in 2nd gear (Lock-up condition) |
294-686 kPa (3.00-7.00 kgf/cm 2, 42.7-99.5 psi) |
Lower limit: 245 kPa (2.50 kgf/cm 2, 35.6 psi) Upper limit: 686 kPa (7.00 kgf/cm 2, 99.5 psi) |
| Torque converter |
Stall speed Check with vehicle on level ground |
|
2, 000 rpm |
1, 800-2, 100 rpm |
| Clutch |
Clearance between clutch end-plate and top disc |
1st, 4th |
1.50-1.70 mm (0.0591-0.0669 in) |
- |
| 2nd, 3rd, 5th, 6th |
1.25-1.45 mm (0.0492-0.0571 in) |
- |
| Countershaft |
Axial clearance of gear |
2nd and 5th gear (total) |
0.04-0.10 mm (0.002-0.003 in) |
- |
| Secondary shaft |
Axial clearance of gear |
2nd and 5th gear |
0.05-0.12 mm (0.002-0.004 in) |
- |
| Third shaft |
Axial clearance of gear |
6th gear |
0.045-0.420 mm (0.002-0.016 in) |
- |
| ATF pump |
ATF pump thrust clearance |
|
0.04-0.07 mm (0.002-0.002 in) |
0.07 mm (0.002 in) |
| Clearance between ATF pump gear and main valve body |
Drive gear |
0.210-0.265 mm (0.009-0.010 in) |
- |
| Driven gear |
0.070-0.125 mm (0.003-0.004 in) |
- |
| A/T differential carrier |
Carrier bearing starting torque (preload) |
For new bearing |
3.9-5.6 Nm (40-57 kgfcm, 35-49 lbfin) |
Adjust |
| For reused bearing |
3.6-5.3 Nm (37-54 kgfcm, 32-47 lbfin) |
Adjust |
| A/T differential pinion gear |
Backlash |
|
0.05-0.15 mm (0.0020-0.0059 in) |
- |
| Transfer assembly fluid |
Capacity |
Fluid change |
0.43 L (0.45 US qt) |
- |
| Overhaul |
0.45 L (0.48 US qt) |
- |
| Recommended fluid |
|
Use Honda HGO-1 |
| Transfer assembly |
Transfer gear backlash |
|
0.06-0.16 mm (0.0024-0.0063 in) |
- |
| Tapered roller bearing total starting torque (preload) |
|
2.64-4.23 Nm (26.9-43.1 kgfcm, 23.3-37.4 lbfin) |
- |