Torque Specifications
WARNING: This page is about a different car, the 2007 Toyota Tacoma. However, it is still accessible from the selected car via links, so may be relevant.
1GR-FE ENGINE MECHANICAL TORQUE SPECIFICATIONS
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Engine under cover sub-assembly No. 1 x Frame assembly | 29 | 296 | 21 | |
| Camshaft bearing cap x Cylinder head sub-assembly | 10 mm (0.39 in.) head | 9.0 | 92 | 80 in.*lbf |
| 12 mm (0.47 in.) head | 24 | 245 | 18 | |
| Chain tensioner No. 1 x Cylinder head sub-assembly | 10 | 102 | 7 | |
| Chain tensioner No. 2 x Cylinder head sub-assembly | 19 | 194 | 14 | |
| Chain tensioner No. 3 x Cylinder head sub-assembly | 19 | 194 | 14 | |
| Camshaft timing gear assembly x Camshaft | 100 | 1,020 | 74 | |
| Camshaft timing gear or sprocket x Camshaft | 100 | 1,020 | 74 | |
| Timing chain cover plate x Timing chain or belt cover sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Ignition coil assembly x Cylinder head cover sub-assembly | 10 | 102 | 7 | |
| V-bank cover x Intake air surge tank | 7.5 | 76 | 66 in.*lbf | |
| Engine hanger No. 1 x Cylinder head sub-assembly RH | 33 | 336 | 24 | |
| Engine hanger No. 2 x Cylinder head sub-assembly LH | 33 | 336 | 24 | |
| Spark plug x Cylinder head sub-assembly | 20 | 204 | 15 | |
| Oil filler cap housing x Cylinder head cover sub-assembly LH | 9.0 | 92 | 80 in.*lbf | |
| Camshaft timing oil control valve assembly x Cylinder head cover subassembly | 9.0 | 92 | 80 in.*lbf | |
| Oil filter bracket sub-assembly x Timing chain or belt cover sub-assembly | 19 | 194 | 14 | |
| Engine mounting bracket front No. 1 RH x Cylinder block sub-assembly | 43 | 435 | 31 | |
| Engine mounting bracket front No. 1 LH x Cylinder block sub-assembly | 43 | 435 | 31 | |
| Engine mounting insulator front No. 1 RH x Frame assembly | 38 | 387 | 28 | |
| Engine mounting insulator front No. 1 LH x Frame assembly | 38 | 387 | 28 | |
| Engine wire No. 2 (ground cable) x Cylinder block sub-assembly | 13 | 133 | 9 | |
| Hood sub-assembly x Hood hinge assembly RH & LH | 13 | 133 | 10 | |
| Hood support RH & LH x Body | 18 | 184 | 13 | |
| Engine rear oil seal retainer x Cylinder block sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Knock sensor x Cylinder block sub-assembly | 20 | 204 | 15 | |
| Water outlet pipe No. 1 x Cylinder block sub-assembly | 10 | 102 | 7 | |
| Cylinder head sub-assembly RH x Cylinder block subassembly | 1st | 36 | 367 | 27 |
| 2nd | Turn 180° | Turn 180° | Turn 180° | |
| Cylinder head sub-assembly LH x Cylinder block subassembly | Recessed head 1st | 36 | 367 | 27 |
| 2nd | Turn 180° | Turn 180° | Turn 180° | |
| 14 mm (0.55 in.) head | 30 | 306 | 22 | |
| Chain vibration damper No. 1 x Cylinder block sub-assembly | 19 | 194 | 14 | |
| Idle gear No. 1 x Cylinder block sub-assembly | 60 | 612 | 44 | |
| Timing chain or belt cover sub-assembly x Cylinder head and block | 23 | 235 | 17 | |
| Water pump assembly x Timing chain or belt cover subassembly | 10 mm (0.39 in.) head | 9.0 | 92 | 80 in.*lbf |
| 2 mm (0.47 in.) head | 23 | 235 | 17 | |
| Oil pan stud bolt x Oil pan sub-assembly | 4.0 | 41 | 35 in.*lbf | |
| Oil pan sub-assembly x Cylinder block and timing chain or belt cover | 10 mm (0.39 in.) head | 10 | 102 | 7 |
| 12 mm (0.47 in.) head | 21 | 214 | 16 | |
| Oil strainer sub-assembly x Oil pan sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Oil pan sub-assembly No. 2 x Oil pan sub-assembly | Nut | 1.0 | 102 | 7 |
| Bolt | 9.0 | 92 | 80 in.*lbf | |
| Oil pan drain plug x Oil pan sub-assembly No. 2 | 40 | 408 | 30 | |
| Crankshaft pulley x Crankshaft | 250 | 2,549 | 185 | |
| Cylinder head cover sub-assembly x Cylinder head subassembly RH | Nut | 9.0 | 92 | 80 in.*lbf |
| Bolt A | 10 | 102 | 7 | |
| Bolt B | 9.0 | 92 | 80 in.*lbf | |
| Cylinder head cover sub-assembly LH x Cylinder head subassembly LH | Nut | 9.0 | 92 | 80 in.*lbf |
| Bolt A | 10 | 102 | 7 | |
| Bolt B | 9.0 | 92 | 80 in.*lbf | |
| Ventilation valve x Cylinder head cover sub-assembly LH | 27 | 275 | 20 | |
| Oil control valve filter plug x Cylinder head sub-assembly | 62 | 632 | 46 | |
| Crankshaft position sensor x Cylinder block sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| VVT sensor x Timing chain or belt cover sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Cylinder block water drain cock sub-assembly x Cylinder block sub-assembly | 25 | 255 | 18 | |
| Oil level gauge guide x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Oil pan sub-assembly x Transmission | 37 | 377 | 27 | |
| Idler pulley sub-assembly No. 1 x Timing chain or belt cover sub-assembly | 54 | 551 | 40 | |
| Idler pulley sub-assembly No. 2 x Timing chain or belt cover sub-assembly | 39 | 398 | 29 | |
| V-ribbed belt tensioner assembly x Cylinder block sub-assembly | 36 | 367 | 27 | |
| Vane pump assembly x Cylinder block sub-assembly | 43 | 438 | 32 | |
| Intake air surge tank x Intake manifold | 28 | 286 | 21 | |
| Surge tank stay x Intake air surge tank and cylinder head | 21 | 214 | 15 | |
| Throttle body bracket x Throttle body with motor and cylinder head | 21 | 214 | 15 | |
| Oil baffle plate x Surge tank stay No. 1 | 9.0 | 92 | 80 in.*lbf | |
| Ground cable x Cylinder head sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Water by-pass joint RR x Cylinder head sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Intake manifold x Cylinder head sub-assembly | 26 | 265 | 19 | |
| Exhaust manifold sub-assembly RH x Cylinder head sub-assembly RH | 21 | 214 | 16 | |
| Exhaust manifold sub-assembly LH x Cylinder head sub-assembly LH | 21 | 214 | 16 | |
| Manifold stay x Exhaust manifold sub-assembly RH and transmission | 40 | 408 | 30 | |
| Manifold stay No. 2 x Exhaust manifold sub-assembly LH and transmission | 40 | 408 | 30 | |
| Cool air inlet No. 1 x Body | 12 | 122 | 9 | |
| Drive plate & ring gear sub-assembly x Crankshaft | 83 | 846 | 61 | |
| Flywheel x Crankshaft | 83 | 846 | 61 | |
| Stud bolt x Cylinder head sub-assembly and cylinder head LH (See page) | A | 4.0 | 41 | 35 in.*lbf |
| B | 9.0 | 92 | 80 in.*lbf | |
| C | 4.0 | 41 | 35 in.*lbf | |
| Union x Cylinder head sub-assembly and cylinder head LH | 15 | 150 | 11 | |
| With Head taper screw plug x Cylinder head sub-assembly and cylinder head LH | 80 | 816 | 59 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Main bearing cap x Cylinder block sub-assembly | 12 pointed head 1st | 61 | 622 | 45 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 12 mm head | 25 | 255 | 18 | |
| Stud bolt x Cylinder block sub-assembly | A | 11 | 112 | 8.1 |
| B | 4.5 | 46 | 40 in.*lbf | |
| Sub-assembly oil nozzle No. 1 x Cylinder block sub-assembly | 9.0 | 92 | 80 in.*lbf | |
| Negative battery terminal | 3.9 | 40 | 35 in.*lbf | |