LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2019 >> Terrain SL >> Repair and Diagnosis >> External Pages >> Different car >> Section 630 (Keyless Entry System And Remote Functions) >> Diagnostic Information and Procedures >> DTC B1513 >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2022 Cadillac CT5. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the harness connector at the T10R Keyless Entry Antenna - Right Body, ignition ON.
  2. Test for less than 1 V between the signal circuit terminal 1 and ground.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If less than 1 V 
    3. NOTE:

    When using the MIN MAX function, autorange on the DMM may not function properly. To ensure accurate test results, turn off autorange and manually set the DMM range to 000.0 V.

  3. Ignition OFF, install a DMM between the signal circuit terminal 1 and ground. Set the DMM to capture DC voltage using the MIN MAX function. Turn off autorange and manually set the DMM range to 000.0 V.
  4. Lock the vehicle doors using the keyless entry transmitter. Activate the antenna by pressing the exterior door handle button/touch pad.
  5. Verify the MAX voltage captured by the DMM is greater than 1 V.
    • If 1 V or less 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If greater than 1 V 
  6. Test for less than 1 V between the low reference circuit terminal 2 and ground.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the low reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If less than 1 V 
    7. NOTE:

    When using the MIN MAX function, autorange on the DMM may not function properly. To ensure accurate test results, turn off autorange and manually set the DMM range to 000.0 V.

  7. Install a DMM between the signal circuit terminal 1 and the low reference circuit terminal 2. Set the DMM to capture DC voltage using the MIN MAX function. Turn off autorange and manually set the DMM range to 000.0 V.
  8. Lock the vehicle doors using the keyless entry transmitter. Activate the antenna by pressing the exterior door handle button/touch pad.
  9. Verify the MAX voltage captured by the DMM is greater than 1 V.
    • If 1 V or less 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the low reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If greater than 1 V 
  10. Replace the T10R Keyless Entry Antenna - Right Body.
  11. Lock the vehicle doors using the keyless entry transmitter. Activate the antenna by pressing the exterior door handle button/touch pad minimum of three times to meet the conditions for setting the DTC.
  12. Verify DTC B1513 is not set.
    • If DTC B1513 is set 

      Replace the K9 Body Control Module.

    • Go to next step: If DTC B1513 is not set 
  13. All OK.
scientia non olet · About LEMON Manuals