LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2018 >> Terrain SL >> Repair and Diagnosis (Single Page) >> Body & Frame >> Windows >> Fixed And MOVEABLE Window System >> Diagnostic Information And Procedures >> Power Windows Malfunction >> Circuit/System Testing >> Test 2

Test 2

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the appropriate electrical connector: S79P Window Switch - Passenger
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 24 & Ground
    • If 10 ohms or greater 
    1. Disconnect Ground Connection
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 24 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On/Vehicle - In Service Mode
  5. Verify a test lamp turns On between the test points: B+ circuit terminal 23 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle - Off & Remove - Test lamp
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for infinite resistance between the test points: B+ circuit terminal 23 & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: S79 Window Switch - Passenger
    • Go to next step: If the test lamp turns On 
  6. Ignition/Vehicle - Off
  7. Connect the electrical connector: S79 Window Switch - Passenger
  8. Disconnect the electrical connector: M74 Window Motor - Passenger
  9. Connect a test lamp between the test points: Control circuit terminal 1 & Control circuit terminal 2
  10. Ignition - On/Vehicle - In Service Mode
  11. Perform the scan tool control function: Passenger Window Motor

    Verify the test lamp state:

    Passenger Window Motor - Stop = Test lamp Off

    Passenger Window Motor - Up = Test lamp On

    Passenger Window Motor - Down = Test lamp On

    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector: S79 Window Switch - Passenger
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points:
      • Control circuit terminal 1 @ Component harness & Ground
      • Control circuit terminal 2 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for infinite resistance between the test points:
      • Control circuit terminal 1 @ Component harness & Ground
      • Control circuit terminal 2 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance
    7. Test for less than 2 ohms between the test points:
      • Control circuit terminal 1 @ Component harness & Control circuit terminal 11 @ S79P Window Switch - Passenger
      • Control circuit terminal 2 @ Component harness & Control circuit terminal 1 @ S79P Window Switch - Passenger
        • If 2 ohms or greater - Repair the open/high resistance in the circuit.
        • If less than 2 ohms - Replace the component: S79 Window Switch - Passenger
    • Go to next step: If the specified state 
  12. Test or replace the component: M74 Window Motor - Passenger
scientia non olet · About LEMON Manuals