LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2013 >> Sierra 1500 XFE >> Repair and Diagnosis >> External Pages >> Different car >> Section 2956 (Object Detection System And Pedestrian Protection System) >> Diagnostic Information and Procedures >> Lane Departure Warning System Malfunction >> Circuit/System Testing

Circuit/System Testing

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 GMC Sierra 3500 HD, 2017 GMC Sierra 2500 HD, 2017 GMC Sierra 1500, 2017 Chevrolet Silverado 3500 HD, and 2017 Chevrolet Silverado 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.

Lane Departure Warning Switch Circuit Malfunction

  1. Ignition ON and all vehicle systems OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 14 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the ground circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify the scan tool Lane Departure Warning Switch Status parameter is Open.
    • If not Inactive 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module.
    2. Test for infinite resistance between the signal circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K109 Frontview Camera Module.
    • If Inactive 
  4. Install a 3 A fused jumper wire between the signal circuit terminal 8 and ground.
  5. Verify the scan tool Lane Departure Warning Switch Status parameter is Closed.
    • If not Closed 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K109 Frontview Camera Module.
    • If Closed 
  6. Test or replace the S48A Multifunction Switch - Instrument Panel.

Lane Departure Warning Switch Indicator Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel, ignition ON.
  2. Verify a test lamp illuminates between the control circuit terminal 2 and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for less than 2 Ω in the control circuit end to end.
    • If the test lamp illuminates 
  3. Ignition OFF, connect the harness connector at the S48A Multifunction Switch - Instrument Panel. Disconnect the X1 harness connector at the K109 Frontview Camera Module, ignition ON.
  4. Verify the lane departure warning switch indicator is not illuminated.
    • If the lane departure warning switch indicator is illuminated 
    1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel.
    2. Test for infinite resistance between the S48A Multifunction Switch - Instrument Panel control circuit terminal 5 and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • If infinite resistance, replace the S48A Multifunction Switch - Instrument Panel.
    • If the lane departure warning switch indicator is not illuminated 
  5. Connect a 3 A fused jumper wire between the control circuit terminal 5 and ground.
  6. Verify the lane departure warning switch indicator is illuminated.
    • If the lane departure warning switch indicator is not illuminated 
    1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the S48A Multifunction Switch - Instrument Panel.
    • If the lane departure warning switch indicator is illuminated 
  7. Replace the K109 Frontview Camera Module.
scientia non olet · About LEMON Manuals