LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2001 >> Jimmy 4D Utility, RWD >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window System >> System Tests >> Test E: Power Window Inoperative-Passenger Door

Test E: Power Window Inoperative-Passenger Door

  1. If diagnostic system check was performed, go to next step. If diagnostic system check was not performed, see DIAGNOSTIC SYSTEM CHECK  under SELF-DIAGNOSTIC SYSTEM.
  2. Turn ignition on, engine off. Operate passenger window from both passenger window switch and master switch. If window operates correctly using both switches, check for intermittent problem. If window does not operate correctly, go to next step.
  3. If passenger window operates correctly from master window switch and not from passenger window switch, go to step  5 . If window does not operate as specified, go to next step.
  4. If passenger window operates from passenger window switch and not master switch, go to step  9 . If passenger window does not operate as specified, go to step  10 .
  5. If vehicle is equipped with a window lockout switch, go to next step. If window is not equipped with a window lockout switch, go to step  7 .
  6. Disconnect passenger power window switch. Using test lamp connected to ground, test master switch lockout signal circuit terminal "F" (Dark Green wire) at passenger power window switch harness connector. If test lamp illuminates, go to step  20 . If test lamp does not illuminate, go to step  8 .
  7. Disconnect passenger power window switch. Connect a test lamp between RAP fuse supply voltage circuit terminal "F" (Dark Green wire) and ground at passenger power window switch harness connector C1. See Figure . If test lamp illuminates, go to step  20 . If test lamp does not illuminate, go to step  28 .
  8. Disconnect side window lockout switch. Connect a test lamp between RAP fuse supply voltage circuit terminal "D" (Dark Green wire) and ground at side window lockout switch harness connector. See Figure . If test lamp illuminates, go to step  19 . If test lamp does not illuminate, go to step  28 .
  9. If driver side window operates from master switch, go to step  22 . If driver side power window does not operate from master switch, see TEST C: ALL POWER WINDOWS INOPERATIVE  .
  10. Disconnect passenger power window motor. Using test lamp connected to ground, probe power window motor UP circuit terminal "B" (Dark Blue wire) at passenger power window motor harness connector. Operate power window motor switch in up direction from power window master switch. If test lamp illuminates, go to next step. If test lamp does not illuminate, go to step  13 .
  11. Using test lamp connected to ground, probe passenger power window motor DOWN circuit terminal "A" (Brown wire) at passenger window motor harness connector. Operate power window in down direction from power window master switch. If test lamp illuminates, go to next step. If test lamp does not illuminate, go to step  14 .
  12. Connect test lamp between power window motor UP terminal "B" (Dark Blue wire) and power window DOWN terminal "A" (Brown wire) at passenger window motor harness connector. Operate power window in up and down directions. If test lamp illuminates, go to step  21 . If test lamp does not illuminate, go to step  22 .
  13. Disconnect passenger power window switch. Using test lamp connected to ground, probe power window master switch UP signal circuit terminal "J" (Light Blue wire) at passenger window switch harness connector C1. See Figure . Operate passenger window in up direction from power window master switch. If test lamp illuminates, go to step  17 . If test lamp does not illuminate, go to step  15 .
  14. Disconnect passenger power window switch. Using a test lamp connected to ground, probe terminal "L" (Tan wire) at passenger power window switch harness connector C1. See Figure . Operate passenger window in down direction from master switch. If test lamp illuminates, go to step  18 . If test lamp does not illuminate, go to step  16 .
  15. Test for an open in power window master switch UP signal circuit (Dark Blue wire). If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  22 .
  16. Test for an open in power window master switch DOWN signal circuit (Tan wire). If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  22 .
  17. Test for open in power window motor UP circuit (Dark Blue wire). If problem if found, repair as necessary and go to step  29 . If problem is not found, go to step  20 .
  18. Test for an open in power window motor DOWN circuit (Tan wire). If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  20 .
  19. Test for an open in master switch lockout signal circuit (Dark Green wire). If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  23 .
  20. Inspect for poor connections at passenger window switch. If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  26 .
  21. Inspect for poor connections at passenger power window motor. If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  25 .
  22. Inspect for poor connections at driver power window master switch. If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  24 .
  23. Inspect for poor connections at side window lockout switch. If problem is found, repair as necessary and go to step  29 . If problem is not found, go to step  27 .
  24. Replace power window master switch assembly. After making necessary repairs, go to step  29 .
  25. Replace passenger power window motor. SeeWINDOW REGULATOR MOTOR  under REMOVAL & INSTALLATION. After making necessary repairs, go to step  29 .
  26. Replace passenger power window switch. See WINDOW SWITCH  under REMOVAL & INSTALLATION. After making necessary repairs, go to step  29 .
  27. Replace side window lockout switch. After making necessary repairs, go to step  29 .
  28. Repair open in accessory voltage circuit. After making necessary repairs, go to step  29 .
  29. Operate system in order to verify repairs.
scientia non olet · About LEMON Manuals