LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2024 >> Expedition Timberline >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine >> Removal And Installation >> Engine Mount RH >> Removal

Engine Mount RH: Removal

NOTE: Discard all engine mount fasteners and install new fasteners.
  1. With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting .
  2. On both sides.Index-mark the hood hinge location.
    GFD859083Courtesy of FORD MOTOR COMPANY
  3. Remove the nuts and the hood.
    GFD859084Courtesy of FORD MOTOR COMPANY
  4. NOTE: LH shown below, RH similar.

    1. Release the clip.
    2. Detach and position the hood shock aside.

    GFD859085Courtesy of FORD MOTOR COMPANY
  5. Remove the CAC intake pipe. Refer to: Charge Air Cooler (CAC) Intake Pipe .
  6. Remove the CAC outlet pipe. Refer to: Charge Air Cooler (CAC) Outlet Pipe .
    • Remove the bolt and position the A/C bracket aside.

    • Remove the nuts and the CAC support.

    GFD859139Courtesy of FORD MOTOR COMPANY
  8. Remove the intake manifold. Refer to: Intake Manifold .
  9. Remove the right rear ignition coil. Refer to: Ignition Coil-On-Plug .
  10. Remove the cowl panel. Refer to: Cowl Panel .
  11. Remove the bolt and pin-type retainers and the air cleaner inlet tube.
    GFD859086Courtesy of FORD MOTOR COMPANY
  12. Remove the pin-type retainers and the air deflector.
    GFD859087Courtesy of FORD MOTOR COMPANY
  13. On both sides.Index-mark the hood hinge location.
    GFD859088Courtesy of FORD MOTOR COMPANY
  14. On both sides.Remove the bolts and the hood hinge.
    GFD859140Courtesy of FORD MOTOR COMPANY
  15. Install the special tools.Install Special Service Tool: 303-F070 Support Bar, Engine., 303-1246 Engine Spreader Bar., 303-1654 Lift Eyes.

    Torque: 25 Nm

    GFD859090Courtesy of FORD MOTOR COMPANY
    • If equipped.Remove the bolts and the transmission housing cover.
    GFD859091Courtesy of FORD MOTOR COMPANY
    • If equipped.Remove the bolts and the underbody shield.
    GFD859092Courtesy of FORD MOTOR COMPANY
  18. If equipped.Remove the bolts and the skid plate.
    GFD859093Courtesy of FORD MOTOR COMPANY
  19. If equipped.Remove the bolts and the skid plate.
    GFD859094Courtesy of FORD MOTOR COMPANY
  20. If equipped.Remove the bolts and the skid plate.
    GFD859095Courtesy of FORD MOTOR COMPANY
  21. If equipped.Remove the front driveshaft. Refer to: Front Driveshaft .
  22. NOTE: Make sure that the mating faces are clean and free of foreign material.

    Remove and discard the LH catalytic converter flange nuts.

    GFD859096Courtesy of FORD MOTOR COMPANY
  23. NOTE: Make sure that the mating faces are clean and free of foreign material.

    Remove and discard the RH catalytic converter flange nuts.

    GFD859097Courtesy of FORD MOTOR COMPANY
  24. NOTE: Only use hand tools when removing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

    Loosen the transmission mount-to-crossmember nuts.

    GFD859098Courtesy of FORD MOTOR COMPANY
  25. Remove the following items:

    1. Remove the starter motor. Refer to: Starter Motor .
    2. Remove the A/C belt. Refer to: Air Conditioning (A/C) Compressor Belt .

  26. Disconnect the A/C compressor electrical connectors and wire retainer.
    GFD859141Courtesy of FORD MOTOR COMPANY
  27. Remove the bolts and position aside the A/C compressor.
    GFD859142Courtesy of FORD MOTOR COMPANY
  28. NOTE: Only use hand tools when loosening or tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

    Remove and discard the RH engine mount through bolt.

    GFD859099Courtesy of FORD MOTOR COMPANY
  29. NOTE: Only use hand tools when loosening or tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

    Remove and discard the LH engine mount through bolt.

    GFD859143Courtesy of FORD MOTOR COMPANY
  30. NOTE: Only use hand tools when loosening or tightening the engine mount nuts and studs or damage to the engine mount can occur.
    NOTE: The engine mount studs may come off with the nuts.

    Remove and discard the engine mount nuts. Remove the engine mount studs.

    GFD859144Courtesy of FORD MOTOR COMPANY
  31. Raise the engine approximately 30 mm (1.18 in).
    GFD859101Courtesy of FORD MOTOR COMPANY
  32. Remove the bolts and the RH engine mount-to-cylinder block bracket. Discard the bolts.
    GFD859145Courtesy of FORD MOTOR COMPANY
  33. Remove the RH engine mount.
GFD859146Courtesy of FORD MOTOR COMPANY
scientia non olet · About LEMON Manuals