| B1111:4B |
Electric Park Brake Enable: Over Temperature |
GO to Pinpoint Test G |
| B1111:53 |
Electric Park Brake Enable: Deactivated |
GO to Pinpoint Test H |
| B1111:54 |
Electric Park Brake Enable: Missing Calibration |
GO to Pinpoint Test F |
| C0609:01 |
Park Brake Switch Circuit: General Electrical Failure |
GO to Pinpoint Test B |
| C0616:9A |
Park Brake Control Module Control Circuit Performance: Component or System Operating Conditions |
GO to Pinpoint Test B |
| C1034:01 |
Park Brake: General Electrical Failure |
GO to Pinpoint Test B |
| C1034:07 |
Park Brake: Mechanical Failures |
GO to Pinpoint Test L |
| C1034:13 |
Park Brake: Circuit Open |
GO to Pinpoint Test B |
| C1034:25 |
Park Brake: Signal Shape/Waveform Failure |
GO to Pinpoint Test B |
| C1034:2F |
Park Brake: Signal Erratic |
GO to Pinpoint Test B |
| C1034:47 |
Park Brake: Watchdog/Safety μC Failure |
GO to Pinpoint Test B |
| C1034:48 |
Park Brake: Supervision Software Failure |
GO to Pinpoint Test B |
| C1034:57 |
Park Brake: Invalid/Incompatible Software Component |
GO to Pinpoint Test B |
| C1034:71 |
Park Brake: Actuator Stuck |
GO to Pinpoint Test C |
| C1034:77 |
Park Brake: Commanded Position Not Reachable |
GO to Pinpoint Test C |
| C1034:78 |
Park Brake: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test I |
| C1034:97 |
Park Brake: Component Or System Operation Obstructed Or Blocked |
GO to Pinpoint Test D |
| C1A43:98 |
Motor Supply: Component Or System Over Temperature |
GO to Pinpoint Test D |
| C2005:18 |
Right Actuator: Circuit Current Below Threshold |
GO to Pinpoint Test D |
| C2005:19 |
Right Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C2005:77 |
Right Actuator: Commanded Position Not Reachable |
GO to Pinpoint Test C |
| C2005:78 |
Right Actuator: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test A |
| C2006:18 |
Left Actuator: Circuit Current Below Threshold |
GO to Pinpoint Test D |
| C2006:19 |
Left Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test D |
| C2006:77 |
Left Actuator: Commanded Position Not Reachable |
GO to Pinpoint Test C |
| C2006:78 |
Left Actuator: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test A |
| C2007:13 |
Right Motor: Circuit Open |
GO to Pinpoint Test D |
| C2007:1C |
Right Motor: Circuit Voltage Out Of Range |
GO to Pinpoint Test D |
| C2007:92 |
Right Motor: Performance Or Incorrect Operation |
GO to Pinpoint Test D |
| C2008:13 |
Left Motor: Circuit Open |
GO to Pinpoint Test D |
| C2008:1C |
Left Motor: Circuit Voltage Out Of Range |
GO to Pinpoint Test D |
| C2008:92 |
Left Motor: Performance Or Incorrect Operation |
GO to Pinpoint Test D |
| U2002:00 |
Switch: No Sub Type Information |
GO to Pinpoint Test K |
| U2002:47 |
Switch: Watchdog/Safety μC Failure |
GO to Pinpoint Test B |
| B1541:11 |
Auto Hold LED: Circuit Short To Ground |
GO to Pinpoint Test E |
| B1541:15 |
Auto Hold LED: Circuit Short To Battery Or Open |
GO to Pinpoint Test E |