Abs Guided Routine Testing - Pinpoint Tests C - H

• Pinpoint Tests C: Brake Booster Vacuum Sensor Faults
  • Notes
  • Possible Causes
  • Visual Inspection and Diagnostic Pre-checks
• Pinpoint Tests CA: Brake Booster Vacuum Sensor Circuit Faults
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
  • Visual Inspection and Diagnostic Pre-checks
• Pinpoint Tests CB: Brake Booster Low Vacuum Fault
• Pinpoint Tests CC: Aspirator Valve Control Circuit Faults
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
  • Visual Inspection and Diagnostic Pre-checks
• Pinpoint Tests CE: ABS Module Communication Concern With HVAC
  • Possible Causes
• Pinpoint Tests CG: The Selectable Drive Mode Feature Is Inoperative, Cannot Be Disabled Or Enabled
  • Normal Operation and Fault Conditions
  • Possible Sources
• Pinpoint Tests CH: The Auto Hold Feature Is Inoperative, Cannot Be Disabled Or Enabled
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Sources
• Pinpoint Tests CI: The Trail Control Feature Is Inoperative, Cannot Be Enabled Or Disabled
• Pinpoint Tests CJ: ABS Module Communication Concern With The Air Suspension Control Module
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CK: ABS Module Communication Concern With The IPMB
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CL: ABS Module Communication Concern With APIM
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CM: ABS Module Communication Concern With HEV PCM
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CN: ABS Module Communication Concern With SIMA
• Pinpoint Tests CO: EBB Unit Internal Failure
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CP: EBB Brake Booster Motor Faults
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CQ: Driver Door Status Correlation Fault
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CR: Hydraulic Brake Booster Flow Switch Stuck On or Off
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
  • Visual Inspection and Diagnostic Pre-checks
• Pinpoint Tests CS: HydroMax Brake Booster Motor Faults
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CU: Hydraulic Brake Booster R Line: Circuit Open
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CV: ABS Module DTC C1A99 - Pressure Sensor
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CW: EBB Brake Pedal Switch Faults
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CX: ABS Module In-Use Application Signing Key Error
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CY: ABS Module Communication Concern With CCM
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests CZ: SASM Communication Concern With FCIM
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests D: ABS Module Communication Concern With BCM
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests DA: SASM Communication Concern With Auxiliary Heater Control Module
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests E: The Traction Control System Is Inoperative Or Cannot Be Disabled Using The Message Center
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests F: ABS Module High Voltage Concern
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
• Pinpoint Tests G: Stability Control Sensor Signal Failure Faults
• Pinpoint Tests H: Hydraulic Pump Faults
  • Notes
  • Normal Operation and Fault Conditions
  • Possible Causes
  • Visual Inspection and Diagnostic Pre-checks