| P0460:11 |
Fuel Level Sensor "A" Circuit: Circuit Short To Ground |
GO to Pinpoint Test C |
| P0460:13 |
Fuel Level Sensor "A" Circuit: Circuit Open |
GO to Pinpoint Test C |
| P1534:01 |
Restraint Deployment Indicator Circuit: General Electrical Failure |
Diagnose all RCM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS)
. |
| P1706:00 |
High Vehicle Speed Observed in Park: No Sub Type Information |
GO to Pinpoint Test AH |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test BS |
| U0101:00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test BT |
| U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test BU |
| U0103:00 |
Lost Communication with Gear Shift Control Module: No Sub Type Information |
GO to Pinpoint Test BV |
| U0104:00 |
Lost Communication With Cruise Control Module: No Sub Type Information |
GO to Pinpoint Test BW |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U0122:00 |
Lost Communication with Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BY |
| U0131:00 |
Lost Communication with Power Steering Control Module: No Sub Type Information |
GO to Pinpoint Test BZ |
| U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test CA |
| U0138:82 |
Lost Communication with All Terrain Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CB |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test CC |
| U0146:00 |
Lost Communication with Gateway "A": No Sub Type Information |
GO to Pinpoint Test CD |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test CE |
| U0151:87 |
Lost Communication with Restraints Control Module: Missing Message |
GO to Pinpoint Test CE |
| U0159:00 |
Lost Communication With Parking Assist Control Module "A": No Sub Type Information |
GO to Pinpoint Test CF |
| U0184:00 |
Lost Communication with Radio: No Sub Type Information |
GO to Pinpoint Test CG |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test CH |
| U0230:00 |
Lost Communication with Rear Gate Module: No Sub Type Information |
GO to Pinpoint Test CI |
| U0230:82 |
Lost Communication with Rear Gate Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CI |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test CK |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
This DTC sets when the IPC receives invalid network data for the speedometer, engine temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID)
, or Refer to: Electronic Engine Controls
. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 |
Invalid Data Received from ECM/PCM A: Invalid Serial Data Received |
This DTC sets when the IPC receives invalid network data for the speedometer or engine temperature data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID)
, or Refer to: Electronic Engine Controls
. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:82 |
Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test BS |
| U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
This DTC sets when the IPC receives invalid network data for the odometer count data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID)
, or Refer to: Electronic Engine Controls
. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test BT |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
This DTC sets when the IPC receives invalid network TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. Refer to: Body Control Module (BCM)
. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0422:82 |
Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CC |
| U0431:82 |
Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CC |
| U0438:81 |
Invalid Data Received From Trailer Brake Control Module: Invalid Serial Data Received |
This DTC sets when the IPC receives invalid network data for off road vehicle pitch display from the TBM for 5 seconds or longer. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TBM and other modules on the network. Refer to: Auxiliary Brake System - Vehicles With: Trailer Brake Control
. If no Diagnostic Trouble Codes (DTCs) are present in the TBM, DIAGNOSE the observable symptom. |
| U0438:82 |
Invalid Data Received From Trailer Brake Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CA |
| U0452:81 |
Invalid Data Received From Restraints Control Module: Invalid Serial Data Received |
This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. Refer to: Airbag Supplemental Restraint System (SRS)
. If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0533:56 |
Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration |
This DTC sets when the IPC receives invalid network data due to configuration mismatch between the IPC and the SODL. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 |
Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CJ |
| U0534:56 |
Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration |
This DTC sets when the IPC receives invalid network data due to configuration mismatch between the IPC and the SODR. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 |
Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CJ |
| U0545:56 |
Invalid Data Received From Running Board Control Module: Invalid/Incompatible Configuration |
This DTC sets when the IPC receives invalid network data due to configuration mismatch between the IPC and the RBM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0557:00 |
Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test CL |
| U0557:81 |
Invalid Data Received From Front Controls Interface Module "A": Invalid Serial Data Received |
This DTC sets when the IPC receives invalid network data for outside air temperature from the FCIM for 5 seconds or longer. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. Refer to: Information and Entertainment System
. If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:82 |
Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test CL |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:46 |
Control Module: Calibration/Parameter Memory Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:46 is retrieved again, A guided routine is not applicable for this vehicle and market. Replace the component that was faulted through diagnosis. |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test CM |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test CN |
| U300A:64 |
Ignition Switch: Signal Plausibility Failure |
DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. Refer to: Steering Wheel and Column Electrical Components
. |