LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2019 >> Taurus SHO >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine - 3.5L Ti-VCT) >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different variant/trim than selected.
Description Nm lb-ft lb-in
A/C compressor bolts and nut 25 18 --
A/C compressor stud 9 -- 80
A/C tube nuts 15 -- 133
Accessory drive belt tensioner bolts 11 -- 97
Battery cable power feed cable nut 5 -- 44
Bellhousing -to-engine bolts 48 35 --
Block coolant drain plug -- RH (1) -- -- --
Block coolant drain plug -- LH (2) -- -- --
Block heater 40 30 --
Block oil gallery plug -- LH (3) 48 35 --
Block oil gallery plug -- rear (3) 85 63 --
Block oil gallery plug -- RH (3) 32 24 --
Camshaft bearing cap bolts (4) -- -- --
Camshaft Position(CMP) sensor bolts 10 -- 89
Connecting rod cap bolts (4) -- -- --
Coolant pump bolts (4) -- -- --
Crankshaft rear seal retainer plate bolts (4) -- -- --
Crankshaft Position(CKP) sensor bolt 10 -- 89
CKP sensor heat shield nuts 10 -- 89
Crankshaft pulley bolt (4) -- -- --
Cylinder head bolts (4) -- -- --
Cylinder Head Temperature(CHT) sensor 10 -- 89
Engine front cover bolts (4) -- -- --
Engine front cover ground wire bolt 10 -- 89
Engine ground wire-to-shock tower bolt 10 -- 89
Engine lifting eye bolts 24 18 --
Engine mount-to-engine nuts 63 46 --
Engine mount-to-frame bolts 90 66 --
Engine oil filter (5) -- -- --
Engine Oil Pressure(EOP) switch (4) -- -- --
Engine-to-bellhousing bolts 48 35 --
Exhaust manifold/catalytic converter manifold bracket nuts -- LH 30 22 --
Exhaust manifold/catalytic converter manifold heat shield bolts 10 -- 89
Exhaust manifold/catalytic converter manifold nuts (4) -- -- --
Exhaust manifold/catalytic converter manifold studs 12 -- 106
Flexplate bolts (4) -- -- --
Fuel supply tube-to-engine front cover bolt 10 -- 89
Generator bolt and nut 47 35 --
Generator B+ terminal nut 17 -- 150
Generator stud 8 -- 71
Ground wire-to-body retainer 10 -- 89
Ground wire-to-engine bolt 10 -- 89
Ground wire-to-RH cylinder head bolt 10 -- 89
Ignition coil-on-plug bolts 7 -- 62
Knock Sensor(KS) bolts 20 -- 177
Lower intake manifold bolts (4) -- -- --
Main bearing bolts (4) -- -- --
Main bearing cap support brace bolts (4) -- -- --
Oil cooler bolts (4) -- -- --
Oil filter adapter (4) -- -- --
Oil pan bolts (4) -- -- --
Oil pan drain plug 27 20 --
Oil pan-to-transaxle bolts 48 35 --
Oil pump bolts 10 -- 89
Oil pump screen and pickup tube bolts 10 -- 89
Piston oil cool valves 4 -- 35
Power Transfer Unit(PTU) 90 66 --
PTU support bracket bolts 48 35 --
Rear driveshaft-to-PTU flange bolts 70 52 --
Skid plate retainers 70 52 --
Spark plugs 15 -- 133
Starter bolt and stud bolt 27 20 --
Starter B+ terminal nut 12 -- 106
Starter S-terminal nut 5 -- 44
Thermostat housing bolts 10 -- 89
Timing chain guide bolts 10 -- 89
Timing chain tensioner bolts 10 -- 89
Torque converter-to-flexplate bolts 55 41 --
Transaxle mount bracket bolt 80 59 --
Transaxle mount bracket nuts 63 46 --
Transaxle mount through bolt and nut 175 129 --
Transaxle-to-engine bolts 48 35 --
Upper intake manifold bolts (4) -- -- --
Upper intake manifold support bracket-to-engine bolt 10 -- 89
Upper intake manifold-to-support bracket bolt 10 -- 89
Valve cover bolts and stud bolts (4) -- -- --
VCT bolts (4) -- -- --
VCT oil control solenoid bolts (4) -- -- --
(1) Tighten to 10 Nm (89 lb-in) plus an additional 720 degrees.
(2) Tighten to 16 Nm (142 lb-in) plus an additional 180 degrees.
(3) Discard original plug and O-ring seal. Install a new plug and O-ring seal to specified torque, no sealer or lubricant required.
(4) Refer to the procedure.
(5) Tighten to 5 Nm (44 lb-in) plus an additional 180 degrees.