LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2019 >> Flex SEL, AWD >> Repair and Diagnosis (Single Page) >> Engine Mechanical >> Mechanical >> Engine - 3.5L Ti-VCT >> Specifications >> Torque Specifications

Torque Specifications

Description Nm lb-ft lb-in
A/C compressor bolts and nut 25 18 --
A/C compressor stud 9 -- 80
A/C tube nuts 15 -- 133
Accessory drive belt tensioner bolts 11 -- 97
Battery cable power feed cable nut 5 -- 44
Bellhousing -to-engine bolts 48 35 --
(1) Block coolant drain plug -- RH
-- -- --
(2) Block coolant drain plug -- LH
-- -- --
Block heater 40 30 --
(3) Block oil gallery plug -- LH
48 35 --
(4) Block oil gallery plug -- rear
85 63 --
(5) Block oil gallery plug -- RH
32 24 --
(6) Camshaft bearing cap bolts
-- -- --
Camshaft Position (CMP) sensor bolts 10 -- 89
(7) Connecting rod cap bolt
-- -- --
(8) Coolant pump bolts
-- -- --
(9) Crankshaft rear seal retainer plate bolts
-- -- --
Crankshaft Position (CKP) sensor bolt 10 -- 89
CKP sensor heat shield nuts 10 -- 89
(10) Crankshaft pulley bolt
-- -- --
(11) Cylinder head bolts
-- -- --
Cylinder Head Temperature (CHT) sensor 10 -- 89
(12) Engine front cover bolt
-- -- --
Engine front cover ground wire bolt 10 -- 89
Engine ground wire-to-shock tower bolt 10 -- 89
Engine lifting eye bolts 24 18 --
Engine mount brace bolt and nut 20 -- 177
Engine mount bracket bolts 30 22 --
Engine mount-to-engine nuts 63 46 --
Engine mount-to-frame bolts 90 66 --
(13) Engine oil filter
-- -- --
(14) Engine Oil Pressure (EOP) switch
-- -- --
Engine-to-bellhousing bolts 48 35 --
Exhaust manifold/catalytic converter manifold bracket nuts -- LH 30 22 --
Exhaust manifold/catalytic converter manifold heat shield bolts 10 -- 89
(15) Exhaust manifold/catalytic converter manifold nuts
-- -- --
Exhaust manifold/catalytic converter manifold studs 12 -- 106
(16) Flexplate bolts
-- -- --
Fuel supply tube-to-engine front cover bolt 10 -- 89
Generator bolt and nut 47 35 --
Generator B+ terminal nut 17 -- 150
Generator stud 8 -- 71
Ground wire-to-body retainer 10 -- 89
Ground wire-to-engine bolt 10 -- 89
Ground wire-to-RH cylinder head bolt 10 -- 89
Ignition coil-on-plug bolts 7 -- 62
Knock Sensor (KS) bolts 20 -- 177
(17) Lower intake manifold bolts
-- -- --
(18) Main bearing bolts
-- -- --
(19) Main bearing cap support brace bolts
-- -- --
(20) Oil cooler bolts
-- -- --
(21) Oil filter adapter
-- -- --
(22) Oil pan bolts
-- -- --
Oil pan drain plug 27 20 --
Oil pan-to-transaxle bolts 48 35 --
Oil pump bolts 10 -- 89
Oil pump screen and pickup tube bolts 10 -- 89
Piston oil cool valves 4 -- 35
Power Transfer Unit (PTU) 90 66 --
PTU support bracket bolts 48 35 --
Rear driveshaft-to-PTU flange bolts 70 52 --
Spark plugs 15 -- 133
Starter bolt and stud bolt 27 20 --
Starter B+ terminal nut 12 -- 106
Starter S-terminal nut 5 -- 44
Thermostat housing bolts 10 -- 89
Timing chain guide bolts 10 -- 89
Timing chain tensioner bolts 10 -- 89
Torque converter-to-flexplate bolts 55 41 --
Transaxle mount bracket bolt 80 59 --
Transaxle mount bracket nuts 63 46 --
Transaxle mount through bolt and nut 175 129 --
Transaxle-to-engine bolts 48 35 --
(23) Upper intake manifold bolts
-- -- --
Upper intake manifold support bracket-to-engine bolt 10 -- 89
Upper intake manifold-to-support bracket bolt 10 -- 89
(24) Valve cover bolts and stud bolts
-- -- --
(25) VCT bolts
-- -- --
(26) VCT oil control solenoid bolts
-- -- --
(27) Tighten to 10 Nm (89 lb-in) plus an additional 720 degrees.
(28) Tighten to 16 Nm (142 lb-in) plus an additional 180 degrees.
(29) Discard original plug and O-ring seal. Install a new plug and O-ring seal to specified torque, no sealer or lubricant required.
(30) Refer to the procedure in this .
(31) Tighten to 5 Nm (44 lb-in) plus an additional 180 degrees.